Tekvox MV41 Plus User Manual Download Page 47

Page: 47 / 47

www.tekvox.com

MV41+

79141-MV User Manual

9. Firmware Upgrade

Prepare the upgrade file (.bin) on the PC, and rename it as “FW_MV.bin”

Power off the switcher and connect the FIRMWARE port of the switcher to the PC with a Type-
A USB cable

Power on the switcher, and the PC will automatically detect a flash drive named “BOOTDISK”

Copy the upgrade file (.bin) onto the “BOOTDISK” flash drive

Close the flash drive, and w

ait for the switcher’s firmware to update

Reopen the flash drive and check for a file named “SUCCESS.txt”. If this file is present, the

firmware has been updated successfully. If the file is missing, then the firmware update has
failed. Double-check the named of the upgrade file, the repeat the previous steps.

Remove the USB cable after the firmware upgrade is complete

Perform a factory reset on the switcher by sending the appropriate command (see

§8.1

System Control

)

Summary of Contents for MV41 Plus















































Search results

Summary of Contents for MV41 Plus

Reviews:

Related manuals for MV41 Plus

Brands by name

Popular brands

Tekvox MV41 Plus, User Manual

Search results

Summary of Contents for MV41 Plus

Reviews:

Related manuals for MV41 Plus

Brands by name

Popular brands