Tektronix WFM4000 Series User Manual Download Page 42

Page: 42 / 79

Getting Acquainted With Your Instrument

Using Online Help

The online help is both a quick and an exclusive reference for instrument operation details. The online help is:

Context-sensitive. The topic displayed depends on what is displayed when the online help is selected or what control is

operated after help is selected.

Navigable. The Contents and Topic Selector panes, along with Links within the topics, provide access to topics.

To Display and Navigate Online
Help

Press

HELP

Use the

GENERAL

knob or the up/down

arrow keys to highlight an entry in the
Contents (entries never change).

Press

SEL

to select the highlighted

category.

Press the right-arrow key to move
selection to the Topic Selector pane
(entries change with the selection made
in steps 2 and 3 ).

Use the

GENERAL

knob and the

up/down arrow keys to select among the
topics listed for the heading selected in
step 2.

Press

SEL

to display the selected topic.

WFM4000 and WFM5000 Waveform Monitors User Manual

Summary of Contents for WFM4000 Series
















































































Search results

Summary of Contents for WFM4000 Series

Reviews:

Brands by name

Popular brands

Tektronix WFM4000 Series, User Manual

Search results

Summary of Contents for WFM4000 Series

Reviews:

Brands by name

Popular brands