Tektronix WFM4000 Series User Manual Download Page 31

Page: 31 / 79

Getting Acquainted With Your Instrument

Setting Display Parameters

You can set up the display parameters using the pop-up menus. In general, they control only settings speci

c to the active

display type. For example, the pop-up menu for the Waveform display enables you to set the Display Mode.

The pop-up menu will appear when selected (see the procedure that follows), unless it is not appropriate for the current
instrument setting (for example, trying to display the Gamut menu when viewing a composite input signal).

Push and hold the display button for
which the settings need to be set or
modi

ed.

When the menu pops up, navigate
through and make your selections as
described in the steps that follow.

Use the right and left keys to traverse
between the menu panels.

Use the up/down arrow keys to select
the parameters in a menu.

Press

SEL

to set the selected parameter.

The

VECTOR

display with the Bar Targets

set to 75% is shown.

NOTE.

The selections in a pop-up menu

can change depending on the settings.

WFM4000 and WFM5000 Waveform Monitors User Manual

Summary of Contents for WFM4000 Series
















































































Search results

Summary of Contents for WFM4000 Series

Reviews:

Brands by name

Popular brands

Tektronix WFM4000 Series, User Manual

Search results

Summary of Contents for WFM4000 Series

Reviews:

Brands by name

Popular brands