Tektronix P6417 Instructions Manual Download | Manualshive

Page: 29 / 40

background image

Maintenance

P4617 & P6418 Logic Analyzer Probe Instructions

19

Install color-coded ring on
the replacement cable and
slide the ring down the tool.

Installation tool

Replacement

cable

Figure 15: Installing the color-coded ring

16. Push the new podlet cable into the rubber comb.

17. Unwrap and remove the masking tape from the splice of the two cables and

discard the faulty cable.

18. Remove the protective 1x2 housing from the new podlet cable. Use the same

procedure as in Step 6 on page 16 to remove the plastic retaining snap.
Discard the retaining snap and the protective housing.

«
...
27
28
29
30
31
...
»

Summary of Contents for P6417









































Reviews:

No comments

Related manuals for P6417

Brand: Kane Pages: 4

Brand: Kamstrup Pages: 100

Brand: Kamstrup Pages: 16

Brand: Kamstrup Pages: 12

Brand: Kamstrup Pages: 60

Brand: Kamstrup Pages: 136

Brand: Kamstrup Pages: 16

Brand: Kamstrup Pages: 155

Brand: Ralston Instruments Pages: 52

Brand: SAGEMCOM Pages: 33

Brand: Saluki Pages: 312

Clavinova CLP-110

Brand: Yamaha Pages: 46

Clavinova CLP-110

Brand: Yamaha Pages: 46

Brand: Yamaha Pages: 8

Brand: Pangea Pages: 2

Brand: MULTISPAN Pages: 2

Brand: AccuMac Pages: 10

SignalHawk SH-36S-PC

Brand: BIRD Pages: 137

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands