TEFAL EXPRESS POWER ZONE, Manual

Page: 13 / 50

11
FR
EN
IT
ES
PT
EL
TR
Setting the temperature
• Iron temperature setting - fig.9 :
- Start with the fabrics to be ironed at a low temperature (•) and finish with those which need
higher temperatures (••• or Max).
- Mixed fibre fabric: set the ironing temperature to the setting for the most delicate fabric.
- Woollen garments: press repeatedly on the steam control button
- fig.6
to obtain short bursts
of steam, without placing the iron on the garment itself.
• Steam output setting:
- Thick fabric: increase the steam setting.
- At a low temperature : set the steam output control dial to the low position.
MODE ECO:
Your steam generator iron has an ECO mode function which uses less power whilst still guaranteeing a sufficient steam flow for you to
iron your garments properly. In order to use this function, once the thermostat of your iron has been correctly set (see table above),
position the steam flow setting on the ECO segment - fig.12 . The ECO mode can be used on all types of fabrics, however, for very thick
or very creased fabrics, we recommend that you use the maximum steam flow for best results.
Dry ironing
• Do not press the steam control button under the iron handle.
Vertical steam ironing
• Set the iron temperature control slide and the steam output control dial (located on the control
panel) to the MAX position.
• Hang the garment on a coat hanger and hold the fabric slightly taut with one hand.
As steam is very hot: never attempt to remove creases from a garment while it is being
worn, always hang garments on a coat hanger.
• Holding the iron in a vertical position - fig.6 , tilted slightly forwards, press repeatedly on the
steam control button (underneath the iron handle) moving the iron from top to bottom - fig.8 .
Refilling the water tank
• When the “tank empty” red warning light flashes - fig.10 , it means that you have no more steam. The water tank is empty.
• Unplug the steam generator. Open the tank filler flap
- fig.4
.
Fill the water tank up without exceeding the MAX level
- fig.4
.
• Close the water tank filler cover.
• Plug in the steam generator. Press the “OK” button - fig.11 , on the control panel to continue ironing. When the green indicator
remains lit, the steam is ready.
Power Zone Function (according to model)
• Your appliance includes the Power Zone function: concentrated steam shot at the tip of the soleplate, to be used in particular
to target stubborn creases, detailing and zones that are difficult to access.
• To use this function, press the Power Zone function on top of the iron as often as necessary
- fig.7
.
Catalysis Autoclean Soleplate
®
• The iron of your steam generator comes with a self-cleaning soleplate which functions by catalysis.
• Its unique coating makes it possible to continually eliminate all the impurities arising from normal usage.
• We recommend you always place your iron on its base or on the iron rest plate in order to protect its self-cleaning
coating.
T
YPE OF FABRICS
SETTING TEMPERATURE
CONTROL
SETTING STEAM OUTPUT CONTROL DIAL
Silk, Synthetics
(polyester, acetate, acrylic, polyamide)
•
Silk, Wool
••
Linen, cotton
•••
SETTING THE TEMPERATURE AND STEAM OUTPUT ACCORDING TO TYPE OF FABRIC TO BE IRONED:
To prime the steam circuit, either
before using the iron for the first
time, or if you have not used the
steam function for a few
minutes, press the steam control
button several times in a row,
holding the iron away from your
clothes
- fig.6
. This will enable
any cold water to be ejected
from the steam circuit.
Recommendations: for
fabrics other than linen or
cotton, hold the iron a few
centimetres from the
garment to avoid burning
the fabric.
1800121673 GV74XX 7lgues_110x154 17/03/11 15:17 Page11