TeeJet UniPilot Pro Installation Manual Download Page 15

Page: 15 / 20

98-05342 R1 EN

UniPilot

Pro

CHAPTER 4 – UNIPILOT PRO HARNESS INSTALLATION

Safety Notes

NOTE: The vehicle must be powered off during the installation of UniPilot Pro harness
NOTE: To prevent the system from any unexpected shut down while operating, check the cable insulation and cable connections to the other

instruments. Route the cables away from all sharp edges to prevent control wires from being pulled hard or damaged.

UniPilot Pro Harness Connections Overview

The typical UniPilot Pro Harness installation includes the components shown below.

Figure 20: UniPilot Pro Harness Components

Aeros 9040

Aeros

Main Harness

45-05884

Matrix

Main Harness

45-05626

Matrix ProGS 840

Matrix ProGS 570

Terminator

45-08101

Terminator

45-08102

SCM Pro

Harness

45-10172

SCM Pro

78-08097 UniPilot Pro

Foot Switch

32-04020

UniPilot Pro

Harness

45-10166

Electric Steering

Device, UniPilot Pro

91-05023

UniPilot Pro

Anti-Rotation Bracket

Kit Generic

65-05246

to Ethernet Interface RJ45 connecto

Seat Switch

Input

Bracket SCM Pro

Flat

65-05251

Assy. Anti Rotation

Pin UniPilot Pro

65-05250

45-05381

DC: xx/xx

Power Cable

45-05381

Summary of Contents for UniPilot Pro





















Search results

Summary of Contents for UniPilot Pro

Reviews:

Related manuals for UniPilot Pro

Brands by name

Popular brands

TeeJet UniPilot Pro, Installation Manual

Search results

Summary of Contents for UniPilot Pro

Reviews:

Related manuals for UniPilot Pro

Brands by name

Popular brands