background image

9

98-05243-ENUS R2

Matrix

®

 Pro

implement – SmartCable or Section driver Module Setup

Implement is used to establish number of boom sections, guidance 

width, spray width, overlap percentage, implement delay on time and 

implement delay off time. 

NOTE:  If a SmartCable or Section Driver Module (SDM) is not present, 

refer to “Single Section Setup” to view setup steps.

1.  Press CONFIGURATION side tab   .
2.  Press 

 Implement 

.

3.  Select from:

►Number of Boom Sections 

#

– used to select the number of 

available boom sections

►Guidance Width 

– used to enter the width between the 

guidelines

►Spray Width 

– used to enter the width of each implement 

section

►Overlap 

– used to select the amount of overlap allowed 

when the boom sections are turned on and off

►Delay On 

– used to enter the timing for the boom section 

valves to switch on

►Delay Off 

– used to enter the timing for the boom section 

valves to switch off

4.  Press RETURN arrow   or CONFIGURATION side tab   to 

return to the main Configuration screen.

NOTE:  Press   or   to switch between Implement setup screens.
NOTE:  Implement settings are only visible and necessary if a 

SmartCable or SDM is installed. If neither is present, see 

Single Boom Setup section.

Figure 1-19: Implement Setup Options with SmartCable or SDM

Configuration

Vehicle

Implement

AutoSteer

Tilt

Lightbar

GPS

Video

Config->Implement

Num Sections

Spray Width

Guidance Width

60.00 ft

12.00 ft

1

Config->Implement (2)

Overlap

Delay Off

Delay On

1.00 s

1.00 s

50%

Summary of Contents for Matrix Pro 570G

















Reviews: