background image

 

 

                                                                                   CenterLine 230BP; Müller SPRAYDOS Installation Manual 

  

 

 

 

                                                                                                                     020-041-UK R5

2

 

 

                                                                                   CenterLine 230BP; Müller SPRAYDOS Installation Manual 

  

 

 

 

                                                                                                                     020-041-UK R5

This installation manual covers installation of CenterLine 230BP with Müller SPRAYDOS 

controllers. We have endeavoured to deliver a fault free product. To ensure optimal use of the 

equipment, we ask you to pay great attention when reading this manual. Regarding responsibility 

for use of the product, we refer to our sales and delivery terms - especially paragraph 7, which fol-

lows:

7. 

Product usage.

7.1  Any use of the product is at the sole risk of the buyer. The  

 

buyer is therefore not entitled to any form for compensation  

 

caused by, for example, any of the following:

•  Disturbance to/from any electronic services or products that do 

not confirm to the standards for CE marking,

•  Missing or poor signal coverage or a succession hereof from exter-

nal transmitters/receivers, used by the buyer,

•  Functional faults, which apply to or from a PC-program or PC-

equipment, not delivered by the seller.

•  Faults that may arise from the buyers negligence to react to warn-

ings and fault messages from the product, or which can be traced 

to negligence and/or absent constant control of the work carried 

out in comparison to the planned job. 

7.2  When implementing any new equipment the buyer must take great  

 

care and pay attention. Any doubts as to correct operation/use    

should result in contacting TeeJet Technologies.

Enjoy work with CenterLine 230BP! 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

               Kind regards,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                      

 

Mølhavevej 2

 

 

 

 

 

 

 

 

 

 

 

9440 Aabybro

 

 

 

 

 

 

 

 

 

 

 

Denmark

 

 

 

 

 

 

 

 

 

 

 

Tel. +45 9696 2500  

 

 

 

 

 

 

 

 

 

 

 

Fax +45 96962501 

 

 

 

 

 

 

 

 

 

 

 

www.teejet.com 

Summary of Contents for Centerline 230BP












Reviews: