TECNICOMAR BICOMPACT Instructions For The Installation, Use And Maintenance Download

Page: 42 / 42

Instructions for the installation, use and maintenance of Tecnicomar watermaker

9-42

WARRANTY CLAIM

A claim shall be made by delivering the part for inspection to an authorized dealer or by giving notice to
Tecnicomar (

- Fax +39.0923.960235) that shall then arrange for the necessary inspection and

repair or replacement (which may be conducted at the facilities of Tecnicomar) provided such service is covered
under this warranty.

RETURN PRODUCT TO TECNICOMAR ONLY AFTER RECEIVING FACTORY
AUTHORIZATION INCLUDING THE ASSIGNMENT OF A RETURN MATERIAL
AUTHORIZATION NUMBER. THIS NUMBER MUST BE CLEARLY MARKED ON THE OUTSIDE
OF THE BOX WHEN SHIPPING

. Buyer shall pay for all related labor and materials and any shipping,

transportation and other expenses associated with the service.

Summary of Contents for BICOMPACT











































Search results

Summary of Contents for BICOMPACT

Reviews:

Related manuals for BICOMPACT

Brands by name

Popular brands

TECNICOMAR BICOMPACT, Instructions For The Installation, Use And Maintenance

Search results

Summary of Contents for BICOMPACT

Reviews:

Related manuals for BICOMPACT

Brands by name

Popular brands