background image

 

Instructions for the installation, use and maintenance  of Tecnicomar  watermaker

  

5-19 

 
If the produced water salinity increases, contact the Tecnicomar Service center. 
 
Follow the SHUT DOWN steps for a correct and safe system power-off: 

 

Depressurize the system by turning the pressure control valve (I) counterclockwise (ignore this point if the unit is 
equipped with the 

automatic pressure regulator

 device). 

 

Push STOP. 

 

Switch off the power supply. 

 

Close the sea water inlet (A2). 

 

5.3 

Manual running mode (c/w 

automatic pressure regulator

 device) 

 
In case you need to pressurize the unit manually: 

Start procedure 

 

Turn the selector automatic/manual located onto the motorized valve (I) in  “manual” position (when the unit is 
off). 

 

Start the unit and turn the handle located top of the motorized valve (I) until reading 60 bar on the display (HObar). 

Stop procedure 

 

Push STOP and turn back the handle top of the motorized valve (I). 

 

Move back the selector automatic/manual located onto the motorized valve (I) in  “automatic” position. 

 

5.4

 

Operation in low- or high-salinity areas 

 
Tecnicomar watermakers may also operate in areas with unknown feed water salinity, like lake or river waters. 
In low-salinity areas the applied operating pressure should be less than 60 bar. In such cases the produced water flow 
rate should be taken under control when applying the operating pressure. 
 

 

The  fresh  water  production  must  never  exceed  the  system  maximum  production  (refer  to  system 
technical characteristic, Section 9). 
 

 

5.5

 

Operation in cold areas 

 
In very cold areas and in high salinity areas there will be a decrease in the fresh water production. In such conditions the 
operating pressure must always be kept at 60 bar (850 PSI). 
 

 

Never operate the watermaker at a pressure exceeding 60 bar (850 PSI) 

 
 

 

 

 

 

Summary of Contents for BICOMPACT











































Reviews: