manualshive.com logo in svg

TECNICOMAR BICOMPACT, Instructions For The Installation, Use And Maintenance

Share
Download
TECNICOMAR BICOMPACT Instructions For The Installation, Use And Maintenance Download Page 4

 

Instructions for the installation, use and maintenance  of Tecnicomar  watermaker

  

1-4 

7.4

 

Membrane flushing with FL/411A and FL/412B chemicals .......................................................................... 7-28

 

7.5

 

General maintenance plan ............................................................................................................................. 7-29

 

7.5.1

 

Prefiltering circuit .................................................................................................................................. 7-29

 

7.5.2

 

Pressurizing circuit ................................................................................................................................ 7-29

 

7.5.3

 

Controls and produced water circuits ..................................................................................................... 7-29

 

7.6

 

Maintenance kit.............................................................................................................................................. 7-29

 

8

 

Common problems and troubleshooting ........................................................................................................... 8-31

 

8.1

 

First start-up .................................................................................................................................................. 8-31

 

8.2

 

Start-up after the replacement of filter cartridges ......................................................................................... 8-31

 

8.3

 

Low pressure failure ...................................................................................................................................... 8-31

 

8.4

 

Low pressure failure during normal operation .............................................................................................. 8-31

 

8.5

 

Operation with vessel in navigation, rough sea and LOW PRESSURE alarm on ......................................... 8-31

 

8.6

 

Normal operation of the watermaker and overload failure shutdown ........................................................... 8-32

 

8.7

 

UNSAFE warning message during normal operation ................................................................................... 8-32

 

8.8

 

The watermaker runs normally but the produced water does not reach the tanks ........................................ 8-32

 

9

 

Technical characteristics and spare parts ......................................................................................................... 9-33

 

9.1

 

Electrophysical characteristics ...................................................................................................................... 9-33

 

9.2

 

A typical analysis of produced water ............................................................................................................. 9-33

 

9.3

 

Spare part list ................................................................................................................................................ 9-34

 

9.3.1

 

High pressure pump ............................................................................................................................... 9-34

 

9.3.2

 

Other spare parts .................................................................................................................................... 9-34

 

9.4

 

Warranty for Tecnicomar equipments ........................................................................................................... 9-41

 

 
 
 

Annexes 

DRAWINGS 

Drawing 1 

FLOW DIAGRAM  

Drawing 2 

CLEANING/STORAGE  

Drawing 3 

WIRING DIAGRAM  

Drawing 4 

AUTOMATIC PRESSURE REGULATOR  

Drawing 5 

ELECTR. CONNECTIONS  

Drawing 6 

AUTOMATIC FLUSHING SYSTEM  

Drawing 7 

PRESSURE VESSEL  

 
 

 

HIGH PRESSURE PUMP (Parts list – exploded view) 

 

LOW PRESSURE PUMP (Parts list – exploded view) 

 

Test certificate 

 
 
 
 
 
 
 

Summary of Contents for BICOMPACT











































Reviews:

No comments

Brands by name

Popular brands

Load more brands