manualshive.com logo in svg

Tecnibel CA250R5TA Series, Installation Manual, Page: 27 / 44

Share
Download
Tecnibel CA250R5TA Series Installation Manual Download Page 27

7-2. Operating Controller Installation

Install the operation controller at the indoor unit intake port
section.
(1)

Fasten the operation controller to the indoor unit intake
port section (electrical component box opposite side)
with the 2 accessory screws (4 x 10).

(2)

Connect the operation controller 4P connector (Blue)
to the WL connector (Blue, CN42) on the indoor P.C.B.

(3)

Install the ceiling panel.

(4)

Connect the indicator section and the operating
controller by 6P connector (white).

(5)

Form the wires with vinyl clampers and fasten.

(6)

Connect the 9P ceiling panel wiring connector to the
9P body connector in the electrical component box.

For cooling only models:
(7)

Disconnect CN8 connector from indoor P.C.B.
(Fig. 7-4).

CAUTION

• Do not twist the operating controller wires together

with the power supply wires. Doing so can result in
malfunction.

• If noise is induced in the unit power supply, take ap-

propriate measures, for example installing a noise fil-
ter.

EG

NOTE

Be sure to remove CN8 connector. If otherwise, the flap
cannot be stopped at a certain position even when the
FLAP button on the remote controller is pressed.

■

CEILING MOUNTED TYPE

7-3. Indicator Section Installation

Remove the side panel to install the indicator section
(Fig. 7-5).
(1)

Remove the side panel.
Open the air intake grille, remove the screw at one
place and then remove the side panel by sliding it
toward the front (arrow direction).

(2)

Remove cover A and cover B.
Put the minus-screwdriver into the recess of cover A
to remove cover A and cover B. (When removing the
cover, take care not to scratch the panel).

(3)

Remove cover B from cover A.

(4)

Install the indicator section at cover A.

(5)

After passing through the lead wires, install cover A
and the indicator section at the panel hole. (The
protrusion part of cover A is fixed with the panel hole).

(6)

Bundle the lead wires along with the wiring of the louver
motor.

(7)

Install the side panel.

Cover A

Cover A

Indicator section

Side panel

 Indicator section

Cover B
(Not used when

 the indicator section 
is installed.)

Air intake grille

Recess

Recess

Panel

Fig. 7-5

26

CR-X253GH

HU (BLK)

CN36

T18 (RED)

CN72

CN10 (YEL)

CN7

CN34

Electrical component box

9P connector

Operating controller

Screws

Fig. 7-3

Fig. 7-4

CN8 (White): LS

Summary of Contents for CA250R5TA Series













































Reviews:

No comments