Technosoft 2016
18
IO-iPOS4808MY Technical Reference
2-3
Connect B2-/CLK- input to J16 pin8 and J17 pin 8 will be
disconnected
JP6
Fdbk#2 DAT+ position
1-2
Connect A2+/DAT+ input to J16 pin5
2-3
Connect A2+/DAT+ input to J16 pin2 and J17 pin 5 will be
disconnected
JP7
Fdbk#2 DAT- position
1-2
Connect A2-/DAT- input to J16 pin15
2-3
Connect A2-/DAT- input to J16 pin3 and J17 pin 6 will be
disconnected
JP8
Ref. 5/10
OFF
Do not connect when JP9=2-3
1-2
Select 0…+5 V analogue Reference
2-3
Select -10…+10 V analogue Reference
JP9
VR1 selection
OFF
Select External analogue Reference or. Feedback. VR1 is not
connected to either signal.
1-2
Select Internal anlg Feedback; use VR1 on analogue Feedback; JP10
must be OFF
2-3
Select Internal anlg Reference; use VR1 on analogue Reference; JP8
must be OFF
JP10
Fdbk. 5/10
OFF
Do not connect when JP9=1-2
1-2
Select 0…+5 V analogue Feedback
2-3
Select -10…+10 V analogue Feedback
JP11
AutoRun
0
Enable AutoRun (normal operation with TMLCAN)
1
Disable AutoRun (if TMLCAN); Disable Setup (if EtherCAT)
JP12
LH3 source
1-2
Connect J18 pin 10 and J19 pin 9 to Z1- (on iPOS)
2-3
Connect J18 pin 10 and J19 pin 9 to LH3 (on iPOS)
JP13
LH1 source
1-2
Connect J18 pin 15 and J19 pin 5 to A1-/Sin- (on iPOS)
2-3
Connect J18 pin 15 and J19 pin 5 to LH1 (on iPOS)
JP14
LH2 source
1-2
Connect J18 pin 14 and J19 pin 7 to B1-/Cos- (on iPOS)
2-3
Connect J18 pin 14 and J19 pin 7 to LH2- (on iPOS)
JP15
Enc Z1 termination
0
Do not connect a 15
0Ω resistor between Z
1+ and Z1-
1
Connect a 15
0Ω resistor between Z
1+ and Z1-
JP16
Enc B1/Cos termination
0
Do not connect a 15
0Ω resistor between B
1+/Cos+ and B1-/Cos-
1
Connect a 15
0Ω resistor between B
1+/Cos+ and B1-/Cos-
JP17
Enc A1/Sin termination
0
Do not connect a 15
0Ω resistor between A
1+/Sin+ and A1-/Sin-
1
Connect a 15
0Ω
resistor between A1+/Sin+ and A1-/Sin-
JP18
Inputs PNP/NPN selection
1-2
Inputs are PNP type; connect to
+Vlog for state change
The inputs type must also be
selected by software, in Setup
2-3
Inputs are NPN type; connect to
GND for state change
JP19
KTY83 sensor for Temp
Mot input
1-2
1mA reference current when using the KTY83 temperature sensor on
Temp Mot (J18 pin12 or J19 pin 4)
2-3
no function