background image

TS Enclosure 530 User Manual 

Rev. 1.

2

 

TS-ENC530 - 13

 

Regulatory Notices 

 

FCC Advisory Statement 

 

!

 

Warning

 

This equipment generates, uses, and can radiate radio frequency energy and if not installed and 

used properly (that is, in strict accordance with the manufacturer’s instructions), may cause 

interference to radio and television reception. It has been type tested and found to comply with 

the limits for a Class A computing device in accordance with the specifications in Subpart J of 

Part 15 of FCC Rules, which are designed to provide reasonable protection against such 

interference when operated in a commercial environment. Operation of this equipment in a 

residential area is likely to cause interference, in which case the owner at his own expense will 

be required to correct the interference. 
If this equipment does cause interference, which can be determined by turning the unit on and 

off, the user is encouraged to try the following measures to correct the interference: 
1.

 

Reorient the receiving antenna. 

2.

 

Relocate the unit with respect to the receiver. 

3.

 

Plug the unit into a different outlet so that the unit and receiver are on different branch 

circuits. 

4.

 

Ensure that mounting screws and connector attachment screws are tightly secured. 

5.

 

Ensure that good quality, shielded, and grounded cables are used for all data 

communications. 

 
If necessary, the user should consult the dealer or an experienced radio/television technician 

for additional suggestions. The following booklets prepared by the Federal Communications 

Commission (FCC) may also prove helpful: 

 

How to Identify and Resolve Radio-TV Interference Problems

 (Stock No. 004-000-

000345-4) 

 

Interface Handbook 

(Stock No. 004-000-004505-7) 

 
These booklets may be purchased from the Superintendent of Documents, U.S. Government 

Printing Office, Washington, DC 20402 
 
 

Summary of Contents for TS-ENC530

















Reviews: