Technogym ACTIVE Wellness TV RUN EXCITE, Machine Configuration

Page: 22 / 38

ACTIVE WTV: Machine configuration
Page 18
MENU –P–
Par. Address Description Value Par. Address Description Value
P-45 411 Motor thermal K 30 P-323 458 Autocap f scan 10
P-60 412 V/f shape 1 P-324 459 Autocap V scan 2
P-61 413 Max out voltage 230 P-325 460 Enc for FlyRes 0
P-62 414 Base frequency 600 P-326 461 Fre for FlyRes 0
P-63 415 V/f interm volt 115 P-340 462 Undervoltage thr 50
P-64 416 V/f interm freq 300 P-341 463 Max pwrloss time 0
P-80 417 Max output freq 100 P-342 464 UV alarm storage 1
P-81 418 Min output freq 0 P-360 465 OV prevention 0
P-100 419 Slip compensate 90 P-380 466 Autoreset attmps 0
P-101 420 Slip comp filter 3 P-381 467 Autoreset clear 10
P-120 421 Manual boost [%] 30 P-382 468 Autoreset delay 50
P-121 422 Boost factor src 0 P-383 469 Autores flt rly 1
P-122 423 Auto boost en 1 P-400 470 Ext fault mode 0
P-140 424 Magn curr gain 30 P-420 471 Volt reduc mode 0
P-160 425 Osc damping gain 10 P-421 472 V reduction fact 100
P-180 426 SW clamp enable 1 P-422 473 V fact mult src 0
P-200 427 Ramp CurLim mode 0 P-440 474 Frequency thr 1 0
P-201 428 Curr lim in ramp 170 P-441 475 Freq prog 1 hyst 5
P-202 429 En lim in steady 0 P-442 476 Frequency thr 2 0
P-203 430 Curr lim steady - P-443 477 Freq prog 2 hyst 5
P-204 431 Curr ctrl P-gain - P-460 478 Const speed tol 5
P-205 432 Curr ctrl I-gain - P-461 479 Const speed dl 1
P-206 433 Curr ctr feedfwd - P-480 480 Heatsnk temp lev 70
P-220 434 En DC link ctrl - P-481 481 Heatsnk temp hys 5
P-221 435 DC-lnk ctr Pgain - P-500 482 Switching freq 9
P-222 436 DC-lnk ctr Igain - P-501 483 Sw freq reduc en 0
P-223 437 DC-link ctr FF - P-520 484 Overmod max lev 0
P-240 438 OverTorque mode - P-540 485 Out Vlt auto adj 0
P-241 439 OT curr lim thr - P-560 486 Deadtime cmp lev 9
P-242 440 OT level fac src - P-561 487 Deadtime cmp slp 50
P-243 441 OT signal delay - P-580 488 Startup display 1
P-260 444 Motor OL prot en - P-600 489 Speed dsply fact 100
P-280 445 Brake res OL en - P-999 490 Param prot code 0
1.2.9. U
P
D
OWN SETTINGS
This function allows access to the parameters in the UpDown table which define the number of
encoder pulses that correspond to different machine incline positions. To access this menu, when
the LED display shows: