
Programming
User Manual -
TP4-20
3-8
Upon initiation of the reception of the emergency SMS, on the display is viewed
Prog.emer SMS Waiting
.
Upon reception of the emergency SMS, on the display is viewed
Prog.emer SMS
Completed
.
Commands available
+
#
to initiate the process
+
CL-EX
to confirm and quit
3.1.7
PROGRAMMING OF THE CODES
From the master programming menu select the submenu codes.
In the code menu the following codes can be programmed:
z
Master (definition of the functions the code is to be enabled for)
z
Standard user (definition of the functions every single one of the 20 codes is to
be enabled for)
Commands available
+
wy
to select the code to be programmed
+
#
to confirm the selection
3.1.7.1
MASTER CODE
The master code is usually reserved to the owner of the system. It is always enabled
for acting on all the programs of the system.
In the master code menu the following parameters can be programmed:
z
Code (programming of the code)
z
Attribute (programming of the function of the code)
Commands available
+
wy
to select the parameter to be programmed
+
#
to confirm the selection
CODE
According to programming effected by the installer it is possible to program a code of
4, 5 to 6 digits.
Commands available
+
wy
to delete an existing code
+
0
...
9
to program the master code
+
CL-EX
to confirm and quit
ATTRIBUTE
The following functions can be programmed:
z
Bypass (enables the code for the bypass of the programs)
z
Bypass general alarms (enables the code for arming of the system in presence of
general alarms, i.e. tamper, low battery, power failure, supervision, trouble
modules)
z
Hold-up (enables the code for the release of a silent alarm in case of hold-up.
The hold-up alarm is released by entering a valid code reducing the last digit by
one, e.g. default master code 12345, hold-up code 12344. If the code ends in 0
(e.g. 12340), the hold-up code ends in 9 (e.g. 12349))
z
Automatic abort on disarming (enables the code for the automatic block of the
alarm call cycles of all the active telephone channels and those waiting upon
disarming of the system)
z
Manual general abort (enables the code for the block of the alarm call cycles of
all the active telephone channels and those waiting entering the master code
again and pressing CL-EX on the console once the system has been disarmed)
z
Disabling remote arming/disarming by telephone (
dis
ables the code from arming/
disarming of the programs by telephone)
z
Disabling direct arming/disarming (
dis
ables the code from direct arming/
disarming, i.e. pressing # (hash) for simultaneous arming of all the programs
enabled)
z
Disabling exclusion (
dis
ables the code from the exclusion of zones (manual or
automatic) upon arming. In case of arming in presence of open zones, these are
activated and release the alarm.)
On the display is viewed current programming:
[ ]
Function disabled
[ # ]
Function enabled
Commands available
+
wy
to select the function
+
#
to enable the function
+
*
to disable the function
+
CL-EX
to confirm and quit
Prog.emer SMS
Completed
Menu 11
Codes
Codes 3
Master code
Master code 1
Code
Master code 2
Attribute
Master code
12345
Summary of Contents for TP4-20
