background image

6

2.2 Receiver control and indication modes

The  receiver  can  work  with  acoustics  or  electromagnetism  sensors.  This  set  is  intended  for 

operation  with  the  electromagnetic  EMD-247  sensor.  The  type  of  the  sensor  is  determined 
automatically. For an acoustic sensor there is only a broadband reception mode, as evidenced by 
the constantly blinking right LED box marked WB. For an electromagnet sensor there are several 
reception frequencies.

The light emitting diode scale executes indication of several functions:
а) this is an indication of a power battery condition,
b) a frequency of the received signal is switched in a circle,    
c) a sensitivity is more-less,                 
d) a volume is more-less.
To understand where you are, one needs to know the following: at startup the scale is checked, 

i.e. consistently included 4 cycles of running lights, then a slight pause, then highlighted the level 
of battery power state for 5 seconds, then the signal strength is displayed.

(when  the  acoustic  «AD-227»  sensor  is  connected  to  the  receiver,  the  filter  frequency  is  not 
displayed);

 5. It is turning into the operating mode, the LED display is indicated by the input signal level at 

a selected frequency:

and a synthesized audio signal is given on headphones.

Turning off the receiver is performing by briefly pressing the button «Power On / Off».

Low input level

High input level

  Activation/deactivation  of  the  receiver.   

The  receiver  turns  on  when  one-time 

pressing the 

«Activation/deactivation of the power»

 button. When you turn on, the device 

consistently:

1. Enable animation plays («running lights» on the LED display);
2. About 4 seconds indicates battery charge (if all the LEDs are lit, than the charge is maximum, 

if the first led light blinks, the device is turned off or the batteries are low):

3. Sound plays when the instrument turns on; 
4. If the «EMD-247» sensor is attached for around 2 seconds, one light emitting diode of the light 

emitting indicator diodes displays the operating filter frequency (for example, 1024 Hz – «1k»),

Weak battery charge

Maximum battery charge

Summary of Contents for Success AG-511N






























Reviews: