background image

Right

Wrong

Wrong

001

001

001

001

012

012

Swing space

Swing space

Swing space

Swing space

Right

21

4>Gently  swing  the  pendulum  and  check 

whether  the  positioning  plate  (001)  swings 

s m o o t h l y .   I f   n o t ,   p l e a s e   r e m o v e   t h e 

positioning plate.

4-1  As  shown  in  the 

fig

ure,  please  check 

whether the 001 positioning panel is correct.

4-2 please check the swing space of the swing 

arm axis is same as shown 

in figure or

 not.

4-3:Please  follow  the  instructions  to  assemble 

the 008 swing arm and the 001 positioning plate.

TECHING

R

After  assembly,  if  the  motion  is  abnormal,  please  check 

whether  the  relevant  moving  parts  are  coated  with 

lubricating  oil  and  the  parts  are  missing  or  misplaced 

according  to  the  instructions.  If  not,  please  follow  the 

steps below to 

nd the problem and solve it.

Troubleshooting

1>whether  the  installation  direction  of  the 

parts is correct.

2>Whether  the  screw  is  tightened  or  not,  is 

it loose?

3>check similar parts for reverse assembly

Horizontal 

line

When the swing arm is 

placed horizontally, the 

eyelet is facing down

Summary of Contents for DM35B








































Reviews: