background image

 ST – 480

reboiler. It is the maximum difference between the set temperature (that
is required in the reboiler) and the current temperature in the reboiler at
which   the   HUW   pump   will   activate.   (for   example:   when   the   set
temperature   has   the   value   of   55

o

  C   and   the   hysteresis   is   5

o

  C.   After

reaching the set temperature, that is 55

o

 C, the HUW shuts down     and

causes activation of the CH pump. Re-activation of the HUW pump will
proceed  when the temperature decreases to 50

o

 C).

III.4. TECH controller

A   room   controller   can   be   connected   to   ST-480   controller.   This

function   allows   to   configure   the   controller   by   selecting   “ON”   option.
Additionally,   the   user   may   check   the   programme   version   of   the   room
controller. 

After connection of TECH controller the user may check and change 

the preset temperature of the central heating system, hot domestic water
and the mixing valve. Additionally all boiler controller alarms are 
displayed. When the operation involves the mixing valve the user may 
preview the current external temperature while viewing the main screen 
with the valve parameters .

After TECH Controller option is enabled a letter "P" appears in the 

upper part of the display in the main screen of the controller. A flashing 
letter "P" indicates that the temperature in the room is too low. As soon 
as the required room temperature is reached the letter "P" stops flashing 
and stays on. 
ATTENTION: No external voltage can be connected to the room controller 
output.

III.5. 

GSM module

NOTE: 

Controlling of this type is possible after purchasing and connecting, to

the controller, the additional control module 

 

 

ST-65

 

  which is not attached to the

regulator as a standard feature.

The   GSM   module   is   an   optional   device   cooperating   with   the   boiler

controller, enabling remote control  of the boiler operation with the use of a
mobile phone. The User is notified with a text message on each alert of the
boiler controller, and by sending an appropriate text message at any time, he or
she receives a return message with the information on the current temperature

- 22 -

Summary of Contents for ST-480

































Reviews: