manualshive.com logo in svg

TECATOR Soxtec System, Manual

Share
Download
TECATOR Soxtec System Manual Download Page 23

ACCESSORIES AND SPARE PARTS

IX:1. ACCESSORIES

(for one piece) Order no

Extraction cups (set of 6) 1000-1462

Cup Holder 1000-1431

Tongs for extraction cups 1529-0007
Thimbles0 26mm(setof25) 1522-0018
Thimbles0 22mm(setof25) 1522-0009

Thimble support (set of 7) 1000-1464

Thimble adapters (set of 6, 0 26 mm) 1000-1466
Thimble adapters (set of 6, 0 22 mm) 1000-1486

Holder for thimble support 1000-1080

Thimble Handler 1000-1467

Extension kit for distribution of hot water and air,

comprimising: 1000-1460

2 ea tubing for distribution of hot water (L = 3 m)

complete with connections

1 ea tubing for distribution of air (L = 3 m

0 4/6 mm) complete with connections

Assembly kit for additional Extraction unit,

comprising: 1000-1461

2 ea Tubing for distribution of hot water

(L = 0.75m)inclT-piececonnection

1 ea Tubing for distribution of air

(L = 1 m, 0 4/6 mm)

Lubricating oil (for Service Unit) 1527-0019

L-,

L

IX:2. SPARE PARTS

For extraction Unit:

Condenser, complete, with recovery and

thimble mechanism 1000-1445

Condenser, glass 1000-1419
Sealing membrane in condenser 1000-1420

Knob for recovery rod 1000-1423

Cylindric seal between condenserand extrac-

tion cup 1000-1424

Valve for hot water and air 1584-0006
Tubing for cold water, 0 8/11 mm, per m 1582-0004
Tubing for hot water, 0 6/12 mm, per m 1582-0023
Tubing for air, 0 4/6 mm, perm 1582-0005

Hot plate, complete 1000-1444
Flat spring for hot plate 1000-1404

Strips, big 1569-0010
Timer 1562-0017

For Service Unit:

Water Pump, complete 1577-0024
Shaft sealing to water pump 1577-0028
O-ring to water pump 1577-0027

p.t.o.

21

Summary of Contents for Soxtec System

































Reviews:

No comments

Brands by name

Popular brands

Load more brands