English
English
3) Method of Working of the Scan Function
When the scan function has found a signal on a channel which is programmed
with the additional muting function, it will test whether the code of the signal mat-
ches to the one which is programmed on the actual channel. In case of mis-
match the scan function pauses only for a short time on that channel. But the
squelch will not turn the loudspeaker on. The green glowing of the control lamp
indicates that the unit has recognised internally the occupation of this channel.
For further information to the additional muting function see point 3 of the chap-
ter "Auxiliary functions of the TeCom-XP".
When pressing the PTT key while the scan function is stepping through the
channels the unit transmits on the transmit frequency of channel 16. When the
pressing of the PTT key occurs while the scan function is resting on a channel,
the unit transmits on the transmit frequency of this channel.
Once a channel is selected for transmit mode, you can send your entire mes-
sage on this channel. After you have released the PTT key the unit will still stay
for a dwell time of 10 seconds on this channel, before the channel searching is
restarted again.
Auxiliary functions of the TEAM TeCom-XP
These functions must be installed into your transceiver by your dealer, before you
can use them. In the description below it is assumed that the functions are active.
Ask your dealer for more details.
1) Transmit Time Limiter
The transmit time limiter ( = time-out-timer ) has the effect of limiting the maxi-
mum time for continuous transmitting on a channel. This transmit duration limit
can be adjusted in steps between 0.5 and 5 minutes by your dealer. If the trans-
mit time exceeds the actual transmit duration limit during your message, the
transmitter will shut off automatically, and you will hear a warning tone in the
speaker. To stop the warning tone and to reactivate the transmitter you have to
release briefly the PTT key and to depress it again.
2) Busy Channel Lockout Function
The lockout function for busy channels has the effect to prevent the unit from
interfering with other stations. If there is a station on the actual channel at the
moment when you press the PTT key, the transmitter will not be switched on. In
this situation you will only hear a warning tone in the speaker. When you release
the PTT key the warning tone will be stopped and the set will revert to receiving
mode. You can only send if there is no station on the actual channel at the
moment when you press the PTT key.
ATTENTION:
> During charging process, do not use the TeCom-XP for radio communication.
The radio should be turned off while charging.
> After charging is finished, remove the radio and the rechargeable battery from
the charger and unplug the AC/DC adapter of the charger from the wall socket.
> Do not attempt to charge alkaline cells or any other accumulator than the sup-
plied one with this charger.
8) Accumulator Alert Indication
The unit is equipped with an accumulator level monitoring circuit which alerts you,
when the stored energy is nearly completely used up. If the accumulator voltage
drops below 5.5 V while transmitting, the control lamp ( 2 ) starts to flash red. But
the transmitter is still working. If you keep on transmitting and the accumulator vol-
tage drops below 5.3 V, you will hear a warning tone in the speaker and the trans-
mitter will switch itself off. After releasing the PTT key and pressing it once again,
the unit will transmit again but only for a short time. Now it is time to recharge the
accumulator. If the unit is in receiving mode, the accumulator voltage can drop
below 3.5 V, until the control lamp ( 2 ) starts to flash red every 5 seconds, accom-
panied by a short warning tone in the speaker. At 3.1 V the unit switches itself off.
9) Energy saving function
The unit is equipped with an energy saving function. This function is factory set
in your unit. This function works only in receive mode. It reduces the current
consumption when no signal is detected on the actual channel and the rotary
channel selector is not turned for at least 10 seconds. If you do not use the unit
for a longer period of time, you should switch it off.
Scan function of the TEAM TeCom-XP
The scan function must be installed into your transceiver by your dealer, before you
can use it. If it is not installed, there is another channel available on position [S] ( =
16 ) of the rotary channel selector. In the description below it is assumed that the
scan function is active. Ask your dealer for more details.
1) Activation of the Scan Function
When you turn the rotary channel selector on position [S] ( = 16 ) the unit runs
through all channels which your dealer has programmed into the unit. If there is
a radio operator signal on one channel which is capable to open the squelch,
the scan function will pause on that channel until it is free again. You can hear
the partner station. 5 seconds after that station has finished its message the
scan function will restart running through the channels.
2) Deactivation of the Scan Function
When you turn the rotary channel selector on a position between 1 and 15 the
scan function is not active.
21
20
Manual_4.qxp 13.01.2007 18:06 Seite 21
