English
English
Mounting of the accumulator
At first turn the rear panel towards you. Place the accumulator
( 9 ) in that way on the unit's rear panel that the 4 slip planes of
the unit grip into the corresponding guiding slots of the accumu-
lator, and that the accumulator's charging contacts show into the
direction of the unit's base. Then push the accumulator under
simultaneous slight pressure on its back into the direction of the
unit's top side, until the latch on the unit's base clicks into place.
Now the unit is ready for radio operation.
If you want to use the unit as a professional transceiver, you have to contact
your local telecommunication authorities. You may be required to pay costs of
registrations and annual fees for every unit and for every frequency. If your
application is passed, you can go to your dealer and let him set your TeCom-XP
to the permitted frequency(ies) and adjustments.
Setting Up the TEAM TeCom-XP
Unpack carefully your UHF radio TeCom-XP. Please check whether the supplied
material matches with the items listed below. In case of loss or damage of a part
contact your carrier at once.
Antenna Charging Mould Mains Adapter Accumulator
Belt Clip Screws Protection cover for double socket
This transceiver is a heavy duty PMR radio, which can be optionally modified by
your dealer also into a professional transceiver. In this unit only the channels 1 - 8
are already factory-preset to the PMR channels, i.e. the number of the rotary
channel selector position corresponds with the actual PMR channel. The positi-
ons 9 - 16 are free according to the factory setting. The TX output power on the
PMR channels is reduced to 500 mW in the radiated field according to the Euro-
pean regulation. See in the chapter "technical data" for the table of the PMR
channel numbers together with the corresponding frequencies. When the unit
remains in pure PMR operation, it is free of charge and registration in most
European countries.
(
6 V / 1300 mAh )
Preface
The TeCom-XP is available in 2 Versions:
TeCom-XP (PMR)
- item no. PR8017
This PMR handheld transceiver can be used without license and registration in the
countries according to the Declaration of Conformity that is included in the scope
of delivery. The radio is equipped with 8 PMR channels ( 446 MHz ) with the max-
imal permitted TX power of 500 mW. Increasing of the TX power is not permitted
and will cause the expiration of the operation permit. The antenna of the radio is
fixed.
TeCom-XP (COM)
- item no. PR8019
The operation of this commercial handheld transceiver requires a license and fees
apply. It can only be operated according to the Declaration of Conformity that is
included in the sope of delivery. The radio can only be operated on authorised,
assigned frequencies in the range between 450 - 470 MHz with the maximal
assigned output power. With the commercial version, the antenna is removable.
17
16
Detaching the accumulator
Turn again the unit's rear panel towards you. To release the
accumulator from the unit you have to pull the latch on the unit's
base with your finger towards the unit's front panel, while pus-
hing simultaneously the accumulator towards the unit's base.
After the accumulator is slid out of the unit's slip planes you can
take it off.
Mounting and removing the belt clip
Turn the rear unit's panel with mounted accumulator towards you.
Mounting: Insert the springy support of the belt clip from above into the
corresponding guide on the back of the accumulator. Push the belt clip
into the direction of the unit's base until the belt clip's latch clicks into
place.
Detaching: The latch of the belt clip is located on the accumulator's
back near the top side. Pull the latch with your fingernail away from the accu-
mulator's back and push simultaneously the belt clip towards the unit's top side.
After the belt clip is slid out of its guide you can take it off.
Operation of the TEAM TeCom-XP
1) Turning the unit On/Off
To turn on the unit rotate the volume control with ON/OFF switch
[OFF] ( 4 ) from its rest position clockwise until you hear a clik-
king sound. 1.5 seconds later a short beep tone will be heard
from the loudspeaker ( 8 ), which indicates that the unit is in
reception mode. To switch off the unit rotate the volume control
with ON/OFF switch [OFF] ( 4 ) counterclockwise to the final stop [OFF] until you
hear a clicking sound. This indicates that the unit is switched off now.
Manual_4.qxp 13.01.2007 18:06 Seite 17
