With norm UK in the version
TS-12vr Full Multi Norm
, you toggle between the EC band and
the UK band, which are indicated by the symbols
EC
and
UK
, by pressing the mode key (7)
[
AM/FM
]. The CB band EU consists of the 40 CEPT channels. The CB band UK consists of
40 channels starting from 27.60125 MHz to 27.99125 MHz.
After turning the radio off, the TS-12vr stores the last channel and the frequency
5) Norm Selection
The version TS-12vr
Full Multi Norm
can be set by the user to the following norms:
DE 80
FM
(26.565 - 27.405 MHz)
, 4 W / 40 AM
(26.965 - 27.405 MHz)
, 4 W
EU 40 FM
(26.965 - 27.405 MHz)
, 4 W / 40 AM
(26.965 - 27.405 MHz)
, 1 W
EC 40 FM
(26.965 - 27.405 MHz)
, 4 W
UK 40 FM
(27.60125 - 27.99125 MHz)
, 4 W / 40 FM
(26.965 - 27.405 MHz)
, 4 W
PL
40 FM
(26.960 - 27.400 MHz)
, 4 W / 40 AM
(26.960 - 27.400 MHz)
, 4 W
EI
40 FM
(26.965 - 27.405 MHz)
, 4 W / 40 AM
(26.965 - 27.405 MHz)
, 4 W
For changing the current norm, please hold the mode key ( 6 ) [
p
] and PTT ( 2) while turning
the radio on. In the display (3), the symbol of the current norm appears, while all other sym-
bols disappear. Select the norm with the channel selector keys (19) and (20) and confirm your
selection by turning the radio off and on again or just press PTT (2) again.
6) Transmitting
To transmit, press and hold the transmission key PTT ( 2 ) at the microphone ( 1 ). The TX sym-
bol will appear in the LED (12).
For best quality, speak normally at a distance of 2 - 4 inches. Speaking too loudly will cause dis-
tortions and make the signal difficult to understand.
While the set is in the transmit mode there is no key entry possible and the receiver is muted.
On completion of the transmission release the PTT key ( 2 ) and the radio will revert to receiv-
ing mode.
7) Priority Channel 9 / 19 [ EMG ]
The TS-12vr contains the priority channels 9 and 19. Priority channel 9 is selected by pressing
the key ( 11 ) [
EMG
] once. To set priority channel 19, press the key ( 11 )
[ EMG ]
twice.
-
8) Receiving Signal Sensitivity [ RF-Gain ]
Signals received at close range may be too strong, the signal sounds distorted. With the RF Gain
function, the received signal can be weakened. With the [RF Gain] key (10), the received signal
strength is reduced by weakening the reception sensitivity. The activated reception sensitivity is
displayed in the LED.
To set the RF amplifier (RF GAIN), press the RFG key only briefly. The display shows r0 to r7. This
value can be changed by pressing the UP/DOWN key. R0 is the highest amplification and at r7 the
RF amplification is the lowest.
English
English
9) Repeater mode
Repeater mode is required for radio operation via a radio relay station to transmit and receive on
different channels. Repeater mode is set as follows:
a) Unit is in the switched-off state
b) Press and hold the EMG button (11) and at the same time the PTT button (2) on the
microphone (1) and switch on the unit.
c) The reception channel and the symbol "r" flash alternately.
d) Now you can set the reception channel with the up/down keys (on the unit or on the microphone).
e) Press the EMG key (11) to select the transmit channel. The transmitting channel and the
symbol "t" flash alternately.
f) Now the transmitting channel can be set with the up/down keys (on the unit or on the microphone).
g) Press and hold the EMG key (11) to enter the preset repeater mode. The unit shows "r" in the
display (3). To exit the mode, press and hold the EMG (11) again for a long time.
10) External speaker jack
The TS-12vr is equipped with a 3.5 mm jack socket ( 18 ) at the rear panel to connect an exter-
nal speaker of 4 - 8 ohm impedance, e.g. TEAM TS-500. At 4 ohms the speaker load can be
4 watts. When the external speaker is connected, the internal speaker will be switched off.
Additional information
1) Safety instruction
Drivers must obey traffic rules regarding the use of transceivers in a vehicle.
The unit radiates RF energy in transmit mode. Please keep an eye on safety distance to the
antenna.
2) General precautions
Protect the mobile radio from humidity and dust. Do not store at places where the tempera-
ture may rise and cause damage, for example in the sun. The set can be cleaned by wiping
with a soft cloth. Do not use chemical products to clean the unit.
3) Servicing
The device must not be opened. Independent repairs or adjustment must not be carried out,
since each modification or unauthorized intervention will result in withdrawal of the operation
permit and of warranty and repair claims. Do not use the mobile radio if it seems not to func-
tion correctly. Disconnect the radio from the DC power source immediately. If there is a
defect, the authorized TEAM specialist dealer or TEAM must be contacted immediately.
4) Conformity
The CB mobile transceiver TEAM TS-12vr complies to the European directive RED
2014/53/EU and meets the European standards EN 300 433, EN 301 489-1/-13, EN 60950-
1 and EN 62311. The Declaration of Conformity is included in this manual.
The specific regulations of the different versions in the different european countries can be found
in the radio passport that is included in this manual.
16
17
man_ts-12vr_1_RoadCOM manual.qxd 05.08.2022 16:00 Seite 16
