background image

INSTRUCTION MANUAL

CCG

TDK­Lambda

<Page>

23/23

9 Before Concluding Power Module Damage

Verify following items before concluding power supply damage.
(1) No output voltage

Is specified input voltage applied?

Are the remote ON/OFF control terminal (RC), output voltage trimming terminal (TRM) correctly 
connected?

For case where output voltage adjustment is used, is resistor or variable resister setting, 
connections correctly done?

Are there no abnormalities in the output load used?

Is the case temperature within the specified temperature range?

Is the ambient temperature within the specified temperature range?

(2) Output voltage is high

For case where output voltage adjustment is used, is resistor or variable resister setting,
connections correctly done?

Is the ambient temperature within the specified temperature range?

(3) Output voltage is low

Is specified input voltage applied?

For cases where output voltage adjustment is used, is resistor or variable resistor setting,
connections correctly done?

Are there no abnormalities in the output load used?

(4) Load regulation or line regulation is large

Is specified input voltage applied?

Are the input terminals and the output terminals firmly connected?

Is the input or output wire too thin?

Is the input or output wire too long?

(5) Output ripple voltage is large

Is the measurement done according to methods described in the Instruction Manual or is it an
equivalent method?

Is the input ripple voltage value within the specified value?

10.  Warranty Period

Warranty period is 5 years.
For damages occurring at normal operation within this warranty period, exchange is free of charge.
Please read the General Safety Instruction before using the products.

Summary of Contents for CCG Series
























Reviews: