background image

FBD120/180/200/220 SECTIONAL GARAGE DOOR OPENER

3

1. Safety Instructions

THESE ARE IMPORTANT SAFETY INSTRUCTIONS. FOLLOW ALL INSTRUCTIONS AS

INCORRECT INSTALLATION CAN LEAD TO SEVERE INJURY OR DEATH

Installation and wiring must be in
compliance with your local building and
electrical codes. Connect the power
supply cord only to properly earthed
mains.

The door opener should be installed and
put

into

operation

by

qualified

personnel. Otherwise, serious personal
injury or property damage may occur.

No one or vehicle is allowed to enter or
leave the garage while the remoter is
being installed, do not allow children to
play near the door.

Before installation of the door opener,
the door should be carefully checked for
being kept well balance. The door must
be in good working order. Open and
close the door manually, make sure the
door can be moved smoothly.

The door opener must be earthed.

Our company reserves the right to
change the design and specification
without prior notification.

Install and adjust the manual
release so that the handle hangs
less than 1.5m above the floor.

The door should only be operated when
it can be observed to avoid accidents.

When opening or closing the door, do
not attempt to walk or drive through the
door.

The operator may only be repaired
with the door closed.

The operator should be disconnected
from mains power to avoid electrical
shock before repairing it or opening its
cover.

Locate any fixed control: within sight of
door but away from all moving parts of
the door and at a height of more than
1.4m above the ground to avoid children
reaching it. Keep remote controls away
from children, to prevent the door
opener

from

being

activated

involuntarily.

WARNING:

Important safety instructions. It is important for the safety of

persons to follow all instructions.

SAVE THESE INSTRUCTIONS.

Failure to comply with the instructions
above may result in personal injury or
property damage. Our company does
not accept responsibility for damage
or injury resulting from installing this
operator.

Summary of Contents for FBD120




















Reviews: