TC Electronic EQ Station Operation Manual Download | Manualshive

Page: 42 / 49

background image

40

VIRTUAL EQ STATION

The VirtualEQ Station enables full control of all features from a Stationary PC, Laptop or Tablet PC via LAN. A PC
with a wireless system gives the ultimate flexibility with “no strings attached”.
Virtual EQ Station is designed to meet the busy live-engineers need for an “easy-to-learn Editor.
If you are familiar with the EQ Station already you will find the Virtual EQ Station extremely easy to operate.This
manual section describes the additional features in the software editor in detail. For detailed information of the
generic features, please refer to the descriptions elsewhere in this manual.

ON/OFF keys

EDIT keys

Channel Select

ADJUST keys

«
...
40
41
42
43
44
...
»

Summary of Contents for EQ Station


















































Reviews:

No comments

Related manuals for EQ Station

Brand: Nakamichi Pages: 21

Brand: Nakamichi Pages: 32

Brand: Yamaha Pages: 2

Brand: Rane Pages: 12

Brand: Klark Teknik Pages: 2

Brand: Pyle Pages: 18

Brand: Ferguson Pages: 13

Brand: Rane Pages: 4

MR Confon Starter f MKII+

Brand: Cambridge Research Systems Pages: 34

Brand: Bigben Pages: 64

Brand: SKP Pro Audio Pages: 12

Brand: Intelix Pages: 8

Brand: JVC Pages: 2

Brand: JVC Pages: 1

Brand: JVC Pages: 25

UXG50 - CD Microsystem With USB Audio

Brand: JVC Pages: 37

Brand: JVC Pages: 27

Brand: JVC Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands