background image

 

 

Choosing the right endurance setup 

The following list recommendations are based on TBS DISCOVERY and TBS DISCOVERY PRO base setups and 

you might already have most of the suggested equipment if you are upgrading an existing platform. 

TBS DISCOVERY / TBS DISCOVERY PRO setup for short range endurance 

flights 

Expected flight time: 20-30 min 

Approximate cost: US$ 2’850 - US$ 3’250 

Experience level: Beginner to Expert 

Ideal for: Parks, R/C clubs, front lawns 

R/C transmitter/receiver: 

Graupner MX-12 2.4GHz radio with bundled receiver (GR-6) 
or Futaba 8FG / 7C 2.4GHz radio with included receiver (R6208SB / R617FS)

Quadrotor equipment: 

1x AerialMob carbon fiber arm set 
4x TBS 4S-6S 30A speed controllers 
4x TBS 400kV LR brushless motors (2x CW, 2x CCW) 
4x T-motor CF 15x5-inch propellers 
1x DJI NAZA V2 flight controller (optional GPS add-on) 

Battery: 

1x TBS 6S (22.2V nom.) 4000mAh 10C LiPo pack 

Battery charger: 

Graupner Ultramat 14S (premium) or TBS B6AC 80W (budget) 

FPV transmitter: 

TBS ROOKIE BOSCAM 5.8GHz 200mW video transmitter 

FPV receiver: 

TBS RC508 5.8GHz video receiver or Dominator 5.8GHz module 

FPV pilot camera: 

TBS 59 or TBS 69 FPV camera 

FPV goggles: 

FatShark Dominator video glasses 

HD camera:

 

GoPro HD Hero 3/3+ Black edition

 

Ground station 
accessories: 

TBS Ground Station 
TBS 3S 5000mAh Ground Station LiPo 
Camera Tripod to mount your gear (e.g. Cullmann Primax 150) 

 

 

 

 

6 

 

Summary of Contents for TBS DISCOVERY




























Reviews: