5
TEMPERATURE/ HUMIDITY ALERT
Press “ALERT” on back of unit to turn temperature &
humidity alert on and off.
1. Hold “
ALERT
” button located on back of home receiver
for 3 seconds to enter the alert setting mode. The indoor
icon will flash.
2. Press “
+
,
-
” to select the between indoor temperature,
indoor humidity or remote sensor channels to be alerted
to. Press “
ALERT
” to confirm your selection. The Upper
pointer and the value on the LCD display will flash, enter
the desired upper limit with the
“
+
,
-
” buttons, press “
ALERT
” to confirm your selection
and then go to the lower limit setting.
3. The Lower pointer and value will flash, enter the desired
lower limit with “
+
,
-
” buttons, press “
ALERT
” to confirm
and exit.
4. You may enter an alert setting for the indoor temp, indoor
humidity and remote sensor temperature.
5. When the temperature hits the limit of your preset levels,
the Upper/Lower pointers and the temperature of the
respective channel (indoor or remote sensor) will flash
and produce an audible alarm. Press any button on the
home receiver to acknowledge and stop the alarm.
6. To deactivate the alert alarm – press “ALERT” until the
upper/lower pointer icons are not shown.
USING THE PROJECTION FEATURE
(Only when powered by adaptor.)
The projection feature will display the time and outdoor/
remote sensor temperature. The projected
TIME
is the same
as shown on the base LCD display. The projected
TEMPERATURE
is same as the remote sensor. To turn the
projection feature on, slide the projection switch on the back
of the unit to the
ON
position.
NOTE: If the projection feature is off, you may press the
SNOOZE button on top of the unit to trigger 5 seconds
of projection.
1. To turn the projected information 180 degrees, press the
SETTING ALARM TIME
1. Hold the “
CLEAR
” button for 3 seconds.
2.
To select either first alarm (A1) or second alarm (A2)
- Press “
+
,
-
” on back to
toggle between selections. Press “
CLEAR
” to confirm your selecton.
3.
Set alarm time
- Press “
+
,
-
” on the back of the unit to enter the desired Hr/ Min
values. Press “
CLEAR
” to confirm.
4.
To view alarm time
- Press “
CLEAR
” button. Alarm time will display for 5 seconds
and then resume to normal clock thereafter.
5.
To select between alarm 1, alarm 2 or alarm off
- Press “
+
“ button on the
back of the unit.
For Daily Alarm - The appropriate “
” icon will appear in the upper left corner of the
time display.
No Alarm - The “
” icons will not be shown.
6. The home receiver will provide either a daily alarm, which last for 2 minutes or a
snooze mode where the alarm will repeat every 10 minutes until manually cleared
(see SNOOZE/LIGHT section below.)
7.
To turn alarm off
- Simply press any button under the LCD display.
8.
To deactivate alarm
- Press “ + “ button on the back of the unit until the alarm icons
are not shown.
SNOOZE/ LIGHT
1. Press the
SNOOZE
/
LIGHT
button for an extended backlight.
2. In snooze alarm mode, press this button to trigger a repetitive snooze alarm.
MIN/ MAX MEMORY SETTINGS
1. Press ”
MIN/ MAX
“ button to view the maximum values for 5 seconds. Press again
to view the minimum values.
2. To clear the memory record, press “
CLEAR
” while the respective values are
displayed on screen.
TEMPERATURE TREND INDICATOR:
In the upper right hand corner of the home receiver LCD display, you will see one
of 3 icons;
will indicate
Rising Temperature
readings if it changes more than
1 degree in an hour
will indicate
Steady Temperature
readings
will indicate
Falling Temperatures
if it is more than
1 degree in an hour.
4
