manualshive.com logo in svg

Tayana TAYANA-48, Owner'S Manual

Share
Download
Tayana TAYANA-48 Owner'S Manual Download Page 34

！

 

The pump should not be allowed to run dry, Switch off 
the FRESH WATER PUMP breaker switch on the DC 
control panel if the tank are empty or if any repairs or 
modification are being carried out to the fresh water 
plumbing system. If the system runs dry it will require 
you to shut off the circuit breaker, refill the tank and 
restart the system.    To assist in reprimand the system 
open the main galley faucet to relieve the air from 
system.    Reset circuit breaker after 20 seconds. 

Cold Water System 

Cold fresh water is distributed by pump to all the head’s wash 
basins, showers, galley, transom shower, toilets,   

The fillers are located both of the port side and starboard side. 

 

The deck filler of water tank 

CAUTION

！

DO NOT LEAVE UNATTENDED

！

CITY 

WATER PRESSURES CAN SINK YOUR YACHT IF A 

FITTING FAILS

！

 

 

33

Summary of Contents for TAYANA-48

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands