Taurus ACCENTO LATTE, Instructions For Use Manual, Page: 17 / 98

POWER ON, RINSE AND PREHEAT FUNCTIONS
• Connect the appliance to the mains.
• Place a container under the coffee outlet to get all the
water for preheating and rinse functions.
• Press the power switch (1), and the coffee machine will
enter a self-check status.
NOTE: Please refer to the section «Troubleshooting» if
any warning appears in this state.
• The manual clean indicator (4.1) will illuminate, and the
power on the switch will flash. The machine will enter into
the self-cleaning and preheating state.
• After doing this process, the single-cup coffee, double-cup
coffee, americano icons and manual bean emptying will
light up.
• After some seconds, the other functions will light up,
indicating both heating elements of the machine (brewing
and steam) are ready to be operated normally.
• The machine goes into standby mode.
BREWING YOUR KIND OF COFFEE
• All the following steps indicate how to brew your coffee
selection properly.
BREWING SINGLE-CUP ESPRESSO
• Place a coffee cup under the coffee outlet.
• Check and make sure the plug of the milk frother is closed
well in place.
• Press the single-cup espresso button (4.8). The appliance
will start to brew a single cup of espresso. The indicator of
the single-cup espresso button (4.8) will illuminate solidly
during the process of brewing a single cup of espresso.
• After brewing a single cup of espresso, the appliance
goes into standby mode automatically.
• During the process, press the single-cup espresso button
(4.8) again if you need to cancel the function.
BREW DOUBLE-CUP ESPRESSO
• Place 1 cup or 2 cups aligned with the coffee outlet.
• Check and make sure the plug of the milk frother is closed
well in place.
• Press the double-cup espresso button (4.7). The appli -
ance will start to brew a double cup of espresso. The
indicator of the double-cup espresso button (4.7) will
illuminate solidly during the process of brewing a double
cup of espresso.
NOTE: The double-cup espresso is achieved by brewing
two cycles of single-cup espresso continuously, so please
do not remove the coffee container during the brewing
process.
• After brewing the double-cup espresso, the appliance
goes into standby mode automatically.
• During the process, press the double-cup espresso button
(4.7) again if you need to cancel the function.
BREW AMERICANO
• Place a coffee container under the coffee outlet.
• Check and make sure the plug of the milk frother is closed
well in place.
• Press the americano button (4.6). The appliance will start
to brew americano coffee. The indicator of americano
(4.6) will illuminate solidly during the process of brewing
americano.
• After brewing an americano, the appliance goes into
standby mode automatically.
• During the function, press the americano button (4.6)
again if you need to cancel the function.
BREW CAPPUCCINO
• Place a coffee mug under the coffee outlet.
• Fill the milk tank with the appropriate amount of cold milk.
NOTE: It is recommended that the temperature of the
milk should be 5-10 °C, and the protein content of milk
should be at least 3%.
NOTE: The milk filled in the milk reservoir should not
exceed the MAX mark on the milk reservoir.
• Insert the milk tube well in place as explained in the milk
tank section in the «Before use» section of this manual.
• Press the cappuccino button (4.5). The appliance will start
to brew a cappuccino.
• After brewing a cappuccino, the appliance goes into
standby mode automatically.
• During the function, press the cappuccino button (4.5)
again if you need to cancel the function.
NOTE: After each use, if there is still milk in the milk res-
ervoir, please store it in the refrigerator, but the silicone
tube and milk frother should be cleaned in time, as it is
explained in the «Cleaning» section of this manual.
NOTE: It is recommended to use a high cup to prevent
the frothed milk from splashing.
• Proceed to clean the milk frothing system, as explained in
the «Cleaning» section.