17
fast flashing (yellow):
P2 channel memory full;
flashing (green):
P1 channel waiting to be cancelled;
always on (green):
cancelling of channel P1 in progress;
flashing (yellow):
P2 channel waiting to be cancelled;
always on (yellow):
cancelling of channel P2 in progress;
Multiple errors are signalled by a 2-second pause between signals.
Should the encoder (obstacle detection) activates while closing, the controller will reverse the direction
and slowly open until the laef reaches its fully opened position. Auto Close function will be deactivated
until a further command pulse is given.
8. RESTORING AUTOMATIC OPERATION
Should the automation need to be operated manually, use the release system. After the manual operation:
• after a Mains Power Failure, such as a black-out (controller remains disconnected for a certain time), the
automation will be moving slowly to allow the Controller to establish its Limits (REALIGNMENT procedure);
• after a Manual Operation without Mains Power Failure (controller remains connected) it will take 4 to 5
complete cycles to complete the realignment procedure. During these cycles, Limits and Soft-Stops will
not be working.
9. 433.92 MHz BUILT-IN RADIO RECEIVER
The radio receiver can learn up to a maximum of 30 rolling codes (BUG2R, BUG4R, K-SLIM-RP, T-4RP) which
can be set on the two channels as required.
The first channel directly commands the control board for opening the automatic device; the second channel
controls directly the pedestrian opening from the controller.
LEARNING SYSTEM FOR RADIO CONTROL DEVICES
P1 = 1
st
channel (OPEN/CLOSE)
P2 = 2
nd
channel (PEDESTRIAN)
1_ Press button P1 briefly to associate a radio control device with the OPEN/CLOSE function;
2_ the (green) DL5 LED is ON to indicate the code learning mode has been activated (if no code is entered
within 10 seconds the board exits the programming function);
3_ press the button of the relative radio control device;
4_ the (green) DL5 LED turns off to indicate saving is complete and then on again immediately waiting for
other radio control devices (if this is not the case, try to re-transmit or wait 10 seconds and restart from
point 1);
5_ to memorise codes to other radio control devices, press the key to be stored on other devices within
2-3 sec. After this time (DL5 LED turns off) must repeat the procedure from point 1 (up to a maximum
of 30 transmitters);
6_ if you wish to save on the 2nd channel, repeat the procedure from point 1 using the P2 key instead of
P1 (in this case the DL5 LED is yellow);
7_ to exit the learning mode without memorising a code, press button P1 or P2 briefly.
If the maximum number of radio controls is reached (30), the LED DL5 will begin to flash
rapidly for about 3 seconds but without performing memorisation.
REMOTE PROGRAMMING BY MEANS OF T-4RP and K-SLIM-RP (V 4.X)
With the new version of software V 4.X it is possible to carry out the remote self-learning of the new version
of transmitters T-4RP and K-SLIM-RP (V 4.X), that is without pressing the receiver’s programming buttons.
It will be sufficient to have an already programmed transmitter in the receiver in order to start the proce-
dure of remote programming of the new transmitters. Follow the procedure written on the instructions of
the transmitter T-4RP and K-SLIM-RP (V 4.X).
CANCELLING CODES FROM RADIO CONTROL DEVICES
1_ Keep button P1 pressed for 3 seconds in order to cancel all the associated radio control devices;
2_ LED DL5 flashes slowly to indicate that the cancellation mode has been activated;
3_ press button P1 again for 3 seconds;
4_ LED DL5 turns off for approx. 3 seconds and then remains steady to indicate that the code has been
cancelled;
ENGLISH
