Tatu Marchesan GNLCR Instruction Manual Download | Manualshive

Page: 24 / 34

background image

22

Marchesan Implementos e Máquinas Agrícolas “TATU” S.A.

GNLCR

1 cm

Working preparation

Important recommendations

• Before working, check the condition of all parts and retighten nuts and bolts,

especially the ones on the disc gangs, otherwise the axis and other fixation components

may be damaged.

• Lubricate all grease fittings appropriately. (See lubrication instructions on pages 26

and 27).

• The drawbar spring must be adjusted

leaving 1 cm (one centimeter) of thread above

the nut and locknut in the rod. This adjustment

must be kept during working and transportation.

• To transport the harrow to longer

distances, it is necessary to use the

transportation lock (A), which is coupled to

the hydraulic cylinder rod.

A

«
...
22
23
24
25
26
...
»

Summary of Contents for GNLCR



































Reviews:

No comments

Related manuals for GNLCR

Brand: Daavlin Pages: 13

Brand: Daavlin Pages: 27

Brand: Eagle Pages: 3

Brand: Backyard Discovery Pages: 79

Brand: Badger Meter Pages: 16

Brand: Cadman Pages: 84

Brand: made for movement Pages: 51

Brand: Labelmate Pages: 61

Brand: Labconco Pages: 62

Brand: Aveo Engineering Pages: 16

Brand: Marani Pages: 35

LIGHT LINEAR PT 1

Brand: LIGMAN Pages: 6

Brand: QRS Pages: 12

Brand: Ikan Pages: 5

Brand: GREAT PLAINS Pages: 190

Brand: HOMCOM Pages: 4

Tracer DO PockeTester

Brand: LaMotte Pages: 19

Brand: Deltech Fitness Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands