taskman Pressure Washer Operator'S Handbook Manual Download Page 6 | Manualshive

Page: 6 / 28

background image

We guarantee under the provisions of the above Directive (2000/14/EC) that
the Sound Power Levels for these equipment models will not exceed:-

PW100PH10 104db
PW100PH11 99db
PW100PH12 104db
PW140PH12 107db
PW150PH8

104db

P

W

150PH11

1

03db

PW150PH12 107db
PW150PH14 106db

PW170PH13

106db

PW170PH15 106db
PW170DY15 114db
PW200PH13 109db
PW200PH15 109db
PW200PH21 108db
PW200DY15 114db
PW9012

106db

We also declare that the above equipment is also in accordance with the
following EC Directives:-

2006/42/EC

2004/108/EC

Bolton

15

.

11

.1

3

P.A.Goulbourne .

Place and date of issue

N

ame and signature or equivalent

marking of authorised person.

Director

Position

The above named person is also responsible for holding the Technical Documentation
applicable to the product to which this declaration relates and may be contacted at the
address which appears at the head of this declaration

Please take care of this document, as duplicate copies are not available.

This document is in accordance with EN45014:1989

«
...
4
5
6
7
8
...
»

Summary of Contents for Pressure Washer





























Reviews:

No comments

Related manuals for Pressure Washer

Brand: GE Pages: 108

Brand: Tatung Pages: 8

Brand: F.F. Group Pages: 40

Brand: Landa Pages: 33

Brand: Task Force Pages: 64

MF200D80WB Series

Brand: Midea Pages: 44

Brand: Kärcher Pages: 56

Brand: Hamron Pages: 23

Porta Stream II

Brand: U-Line Pages: 9

Brand: Ingco Pages: 16

Brand: Indesit Pages: 12

Brand: Electrolux Pages: 26

Brand: Electrolux Pages: 15

Brand: Electrolux Pages: 21

Brand: Electrolux Pages: 24

Brand: Electrolux Pages: 15

Brand: Electrolux Pages: 25

Brand: Electrolux Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands