28
Cleaning the machine
Storage / parking of machine (machine is idle)
Store the machine with the tank cap slightly open, by:
• lifting the tank lid and turning the dosing aid upside down.
• then rest the tank lid on the dosing aid.
Service, maintenance and care
The machine's maintenance is a pre-condition for trouble-free running and a
long life.
Service intervals
TASKI machines are build to the highest quality standards . This is supported
by internationally recognised quality control procedures. Electrical and
mechanical parts are subject to wear or aging if used for long periods of time.
Service centre
Should you contact us due to a malfunction or for placing an order, please
always state the type, description and the serial number of your machine.
You can find this information on the name plate of your machine, and the
address of your nearest TASKI partner can be found on the last page of this
manual.
Blades replacement
Blade on the inner radius.
Blade on the outer radius
Cleaning or replacing the float (Indication for full recovery tank)
Disassembly:
Assembly:
Optimal result can only be obtained with clean and intact blades!
Caution:
Never clean the machine with high water pressure or a water
hose.
The ingress of water into the machine might cause considerable
damage to mechanical or electrical parts.
• Wipe down the machine with a damp cloth.
We recommend that you disconnect the battery from the machine
using the battery disconnection socket when storing / parking the
machine and when charging the battery.
The dosing aid holds the tank lid slightly open,
allowing the tank to dry out. As a result, the
formation of mould and unpleasant smells can
be reduced.
Caution:
Only TASKI branded spare parts must be used, otherwise
warranties and liabilities will be omitted!
Symbols:
◊
= After use,
◊◊
= Every week,
◊◊◊
= Every month,
⊗
= Service light
Activity
◊ ◊◊ ◊◊◊ ⊗
page
Recharge batteries
24
Refill distilled water (wet batteries). Please follow
the manufacturers instructions of use booklet for
these batteries!
Clean all parts marked yellow
Drain and clean the tanks
27
Wipe down the machine with a damp cloth
28
Clean the tank lid seal, check for cracks and re-
place if necessary
Maintenance programs by TASKI service made by
TASKI technician
• In order to ensure operational reliability and
availability for use, the service must be carried
out when the service indicatior lights up (factory
setting 450 working hours) or at least once a
year.
Under rough or extreme working conditions and/or insufficient maintenance,
shorter periods are necessary.
• Place the clean squeegee unit with the outer radius face down on a solid
surface e.g. table, floor.
• Press one hand onto the squeegee body by the hose connector.
• Grasp the blade with your thumb and forefinger in the middle of the arch and
pull strongly until the metal band clicks open and the blade is released from
the squeegee body.
• Release the metal strap and pull the blade off the squeegee body.
• Clean squeegee (body, metal straps and blades) with a brush.
• Mount the "rotated" or replaced blade onto the squeegee body.
• Lock the metal strap (Check position of mounting slots) into place and press
the centre of it until it ”clicks” into place and presses the blade onto the
squeegee body (Risk of injury).
• Turn the squeegee upside down by placing it on its suction hose connector
and the bumper wheels.
• Realease the metal band by loosening the fixation screw (torx 25).
• Release the metal band and pull the blade off the squeegee body.
• Clean squeegee (body, metal straps and blades) with a brush.
• Mount the "rotated" or replaced blade onto the squeegee body.
• Hook the metal strap into place (Check position of mounting slots) and fix it
with the screwdriver until the blade is pressed onto the squeegee body.
• The shape of the blades allow them to be used on all sides before needing
replacement.
• Switch the machine off using the keyswitch and remove the key.
• Hold the float and pull it over the lower stopper.
• Clean it with water using a brush (let it dry out well).
• Brush the yellow suction filter with a soft brush
or remove the fluff with a cloth.
The yellow suction filter can be easily removed
(quick-fit seal).
• Hold the float at its small diameter. Push it over
the lower stopper until it clicks into place.
• Check:
-that the float easily moves up and down.
-that the float completely covers (seals) the suction filter.
