4 - Advanced functions
TASCAM DA-45HR
25
You can start the tape’s program numbers from a
value different from
01
by turning the
DATA
dial.
The program number selected with the
DATA
dial
will flash (the flashing will continue for five
seconds).
Confirm the flashing program number with the
ENTER
key. If you press
ENTER
after the program
number has stopped flashing, renumbering will start
from 01.
The tape will rewind to the first START ID, and
rewrite the ID in the same location as previously, but
with the number selected above.
When this is done, the number at the right of the dis-
play will change to the number which is one greater
than the starting program number, and the tape will
move forward to the next START ID and renumber it
in the same way.
While a START ID is being rewritten, the word
RENUM
will flash in the display, and the
PLAY
and
RECORD
indicators will light.
If the current START ID already has a number, this
will be shown to the left of the
#
mark on the
display:
If the current START ID is unnumbered, this is repre-
sented by a pair of dashes in the
PNO
location on the
display.
All program titles are retained during the renumber-
ing process.
The renumbering process continues until the end of
the tape or an END ID is reached.
NOTE
Valid program numbers are from 01 to 99. If
the above procedure is used to select a pro-
gam number at the high end of the range, and
the renumbering increments a program num-
ber above 99, the number will “wrap” to 00.
The number 00 can cause problems when
searching and locating, and this should be
remembered when setting program numbers.
4.5 The EDIT key
The
EDIT
key (
SHIFT
ed
MENU [28]
) allows the
following operations to the performed:
• Editing of the first memory location
• Editing of the second memory location
• Editing of a programmed sequence of programs for
subsequent playback
• Editing of a string of characters to be used as a tape
or program title
• Writing a string of characters to tape
Repeated presses of
EDIT
will cycle through these
options.
To exit the EDIT mode, press
COUNTER MODE
or
DISPLAY
(as with all
SHIFT
ed modes, pressing the
SHIFT
key so that the
SHIFT
indicator goes out will
exit the
SHIFT
mode).
The
ENTER
key is used to select the operation.
4.6 Location memories
4.6.1 Locating to location memories
Once a memory location has been set, as explained
below, use the
LOC 1
and
LOC 2
keys to locate to
the memory location points (as explained in
LOC 1
[29]
).
4.6.2 Setting location memories
Press the
MEMO 1
or
MEMO 2
key. The current
location will be stored to frame accuracy, regardless
of whether or not the frame display mode is currently
in operation, in memory location 1 or 2 as
appropriate.
4.6.3 Editing location memories
Press
EDIT
until the display shows either
M1?
or
M2?
at the right, together with the location value
stored in that location memory.
Press
ENTER
to start editing the location memory.
The word
Edit
will appear at the right of the dis-
play, and the right digit of the frames field will start
to flash.
Use the
SHUTTLE
wheel to move the cursor (flash-
ing digits) between the frames, seconds, minutes and
hours fields.
Use the
INS/+
and
DEL/-
keys and the
DATA
dial to
increment or decrement the flashing value field.
PNO
0
0
H
2
3
M
1
7
s
0
2
#
0
3
0
0
H
2
8
M
5
3
S
2
9
M
1
?
0
0
H
2
8
M
5
3
S
2
9
E
d
i
t
Summary of Contents for DA-45HR
Page 9: ...TASCAM DA 45HR 9...
