17
We carry out all repairs in the shortest possible time and at
the most economical prices. (See front page for address
and phone numbers) Contact your authorized TARGET®
dealer concerning maintenance and repairs.
For quick supply of spare parts and to avoid any lost time, it is
essential to quote the data on the manufacturers plate fixed to
the machine and the part number(s) and description to be
replaced with every order.
ANGLE GUIDE
PROTRACTOR PRECISION MITERING GUIDE
BULLNOSE FOLDING STAND
Parts List:
Diag.
Part No.
Qty.
Description
Diag.
Part No.
Qty.
Description
1
161479
1
Frame, Miter
10
1
Protractor Arm
2
050107
1
Bar, Locking
11
020011
1
Bolt, Carriage, 1/4-20 x 5/8”
3
050105
1
Clip, Stop
12
020244
1
Wing Nut, 1/4-20
4
050106
1
Spring
13
020598
1
Screw, Thumb, 1/4-20 x 1”
5
050103
1
Knob
14
051010
1
Protractor Assy
6
020598
2
Screw, Thumb, 1/4" - 20 x 1"
15
020598
1
Screw, Thumb, 1/4" - 20 x 1"
7
051020
1
Miter Assy, 45
°
16
051030
1
Holder Assy, Bullnose
8
020598
1
Screw, Thumb, 1/4" - 20 x 1"
17
051041
1
Stand, Tile Saw
9
————
1
Protractor Head
18
050102
1
Support Assy, Miter Frame
RIP GUIDE: P/N 051000 - The Rip Guide is a standard
accessory supplied with every tile saw. It is used to
provide a repeatable position for rip cuts until relocated. The
Rip Guide clamps to the machined backstop of the conveyor
cart.
ADJUSTABLE PROTRACTOR: P/N 051010 - The Pro-
tractor can be used to rip cut known angles. The protractor
clamps to the backstop.
ANGLE GUIDE : P/N 051020 - This is a non-adjustable
miter used to quickly position the tile at 45 degrees; either on
the left or right side. It is often used for repeated
diagonal rip cuts. The Angle Guide clamps to the backstop.
BULLNOSE MITERING GUIDE: P/N 051030 - This is a
fixed guide that positions the tile for a 45 degree miter cut.
The Mitering Guide clamps to the backstop.
PRECISION MITERING JIG: P/N 161480 - This is a 45
degree fixture that has an adjustable clamp to hold the tile
while miter cutting. The Mitering Guide clamps to the
backstop.
BOOMERANGLE: P/N 169525 - This plastic accessory
holds the tile at 45 degrees; locating two edges of the tile.
Useful for diagonal cuts or uniformly cutting off corners. The
Boomerangle clamps to the backstop with two thumb screws.
FOLDING STAND: P/N 051041 - This stable, one piece
stand brings a TARGET® tile saw to standing level for ease
of work. The stand conveniently folds flat for storage and
transporting.
The instructions for use and spare parts found in this
document are for information only and are not binding.
As part of our product quality improvement policy, we
reserve the right to make any and all technical
modifications without prior notice.
The manufacturer accepts no
responsibility caused by unsuitable
use or modifications.
11
REPAIRS
13
TILE CUTTING ACCESSORIES
12
SPARE PARTS
Summary of Contents for SUPER TILEMATIC STM10100
