background image

TESTING THE  OPERATION

The correct operation of the system can be tested after
the TARGET LT400 has been installed according to the
instructions.

1. Switch the system on by starting the vehicle
(if the switch has been added then it must be
set to ON).

Result: 

The system emits a short audio signal and the

LED is switched on for 2 seconds. The LT400 will be in
test mode for 10 seconds.

2. Test the operation of the laser receiver using an
infrared remote control device (for audio or video
equipment). Hold the remote control device in
front of the transponder lens (at a distance of
approximately 10 cm) and at the same time press
a button of the remote control device. 

Result:

The system emits a warning signal and the

LED is switched on. 

3. Stop pressing the button of the remote control
device when you are satisfied that the system is 
functioning correctly.

Result:

After the last received signal the LED will be

switched on for 10 seconds. After the 10 seconds have
elapsed the system will emit two short audio signals. 
The LT400 is now in the stand-by mode.

IMPORTANT INFORMATION
FOR ALL USERS

Check frequently whether the lens of the transponder
is dirty. The effect of dust and grit on the function-
ing of the system is very limited. Objects that cover
the lens completely, such as leaves or insects, should
be removed at once.

Check frequently whether the housing and the lens
of the transponder show signs of damage. 
Contact your dealer if the lens is damaged. 

A dealer should check the tuning of the transponder
periodically (for example, when the vehicle is 
serviced).

ENGLISH

9

Summary of Contents for LaserTrack LT400















Reviews: