Target FS 1218 EX Operating Manual Download Page 22

Page: 22 / 24

DRAFT

- 22 -

19.0

Hydraulic – troubleshooting

If the hydraulic system does not work, carry out the following control:

1. Are the battery cables connected to the battery?

2. Is the main switch for the 12 V systems switched on?

3. Is the battery fresh and recharged?

4. Is the oil level at the 3/4 spot on the oil reservoir?

When all above seems to be correct, and it still does no work, the magnetic valve (3) can be out
of order or blocked.

Cleaning the valve.

Step1.

Remove part no. (1) and (2) and unscrew the magnetic valve no. (3).

For best possible cleaning result we are recommended to use compressed air.
Blow inside as well as outside the valve before all parts are replaced.

Step 2.

If cleaning does not give sufficient result, change the magnetic valve.

Step 3.

If nothing above helps, you my have an electrical wiring problem, or some
technical problem with the hydraulic unit.

Call for assistance.

Summary of Contents for FS 1218 EX

























Search results

Summary of Contents for FS 1218 EX

Reviews:

Related manuals for FS 1218 EX

Brands by name

Popular brands

Target FS 1218 EX, Operating Manual

Search results

Summary of Contents for FS 1218 EX

Reviews:

Related manuals for FS 1218 EX

Brands by name

Popular brands