background image

We recommend that all cables have tinned ends for better electrical contact.

In case of power bus bar using, avoid tightening with extenders on the allen wrench, as excessive torque may 
break the the terminal.

1 - SMART COOLER:

 This amplifier has two internal ventilation fans. For perfect functioning, the amplifier must 

be installed in a cool and aired place with at least 1” (25mm) space around the heasink for proper heat spreading. 
The usually working temperature of amplifier is 65°C.

2 -  POSITIVE  POWER  SUPPLY: 

Use a minimum 4  AWG up to maximum of 1/0  AWG cable direct from the 

positive battery terminal, with fuse or circuit breaker (200A), as close to it as possible.

3 - TERMINAL REMOTE: 

It must be connected to the remote output of the head unit using a 18 AWG cable.

4 - NEGATIVE POWER SUPPLY: 

Use a cable of minimum 4 AWG up to maximum of 1/0 AWG as short as possible, 

connected to the negative battery pole.

10

Power supply connector 

The thermal protection waits for cooling before restarting.

Low Battery Protection:

 Working amplifier       Red LED (LED Monitor) or Smart LEDS, flashes 2x        Red LED 

(LED monitor) or Smart LEDS, flashes 2x         Amplifier restarts.

If it goes into protection, the amplifier will automatically restart.

Example:

LEDS indicators & protection system

            

amplifier

Working 

below 9V

Battery with voltage 

Battery with voltage

above 16V

Temperature above operating 

limit (> 85 ° C)

 Led of Monitor 

Conditions

Smart LEDs

On - Displays audio 
level.

LEDs flashing 2x

LEDs flashing 3x

LEDs flashing 
6x per second
Continuously

LEDs flashing
1 second on
1 second off

Blue LED on

Red LED
flashes 2x

Red LED
flashes 3x

Red LED
flashing 6x per
second continuously

Yellow LED
flashing 1 sec. on
1 sec. off

2x

3x

Short circuit on output or 

between output terminal to GND

ENGLISH

POWER 

INPUT

1

1

2

3

4

The fan and ventilation openings are responsible for cooling the amplifier when it is in 
use, so it cannot be obstructed.

CAUTION

Before making any connections to the power terminals, make sure that the negative (-) 
of the vehicle battery is disconnected.

CAUTION

Summary of Contents for SMART3BASS















Reviews: