Tapco Port-O-Slitter General Instructions, Set Up, Accessories And Manual To Using Download Page 5

Page: 5 / 8

Port-O-Slitter Motor Kit Setup/Parts List

STEP 1

Attach steel connector brackets to the motor base plate
using 1/4-20 x 7/8" hex bolts, 1/4" flat washers and 1/4-20
Nylox hex nuts. Do not tighten brackets yet.

STEP 2

Align motor base plate to slitter base plate making sure
the holes in the brackets line up with the holes in the
slitter base plate. Fasten both base plates together using
the above mentioned hardware. Once you have both base
plates in line, tighten all fasteners securely.

STEP 3

Insert the 7/8" coupling flange onto the reducer shaft and
align the key ways. Slide the key in place. Next, insert the
3/4" coupling flange onto the slitter shaft and align the set
screw over the flat of the shaft surface.

STEP 4

Set the reducer onto the motor base plate with the cou-
plings facing each other. Place the sleeve between each
coupling flange and draw together so the ends of the
sleeve are firmly seated inside.

STEP 5

Insert 4 each 1/4-20 x 1" socket cap screws up through
the bottom of the motor base plate and into the reducer
base block. After making sure the coupling assembly is
securely positioned onto both shafts, tighten the socket
cap screws and the set screws positioned both over the
key stock, and over the flat of the shaft on the slitter.

STEP 6

to install the motor, first align the keyways on the shafts
and insert the key as you slide the motor shaft into the
reducer shaft, insert 4 each 3/8" bolts and lock washers
through the reducer housing and into the motor until snug.

STEP 7

Plug power cord into outlet and familiarize yourself with
the forward and reverse positions of the toggle switch. To
activate motor, depress foot switch, To deactivate motor,
release foot switch. To lock out the foot switch, position
the toggle in the center or upright position. Avoid the use
of extension cords between motor and outlet.

Part No. Description

10631

Foot Switch

10632

Foot Guard

10633

Toggle Switch

10627

Slitter Motor

10639

Worm Gear Spacer

10640

Worm Gear Drive

10628

7/8" Coupling Body

10629

3/4" Coupling Body

10630

Coupling Sleeve

10635

Base Connector

10520

1/4-20 Nylock Hex Nut

10095

1/4" Flat Washer

10634

Slitter Motor Base

10636

1/4-20 x 1" Sock Cap

10799

1/4-20 x 1" Hex Wash HD

10770

1/4" Lock Washer

PORT-O-SLITTER MOTOR KIT

Summary of Contents for Port-O-Slitter









Search results

Summary of Contents for Port-O-Slitter

Reviews:

Related manuals for Port-O-Slitter

Brands by name

Popular brands

Tapco Port-O-Slitter, General Instructions, Set Up, Accessories And Manual To Using

Search results

Summary of Contents for Port-O-Slitter

Reviews:

Related manuals for Port-O-Slitter

Brands by name

Popular brands