manualshive.com logo in svg

TANDBERG TT1220 Series, Instruction Manual

Share
Download
TANDBERG TT1220 Series Instruction Manual Download Page 92

Menus

Page C-14

Instruction Manual: Professional Receivers and Decoders (IRD)

ST.TM.TT1220.1

Display title: STATUS: ALARM

Description

Section

VBI

Enters the VBI alarm status submenu

Audio

Enters the Audio alarm status submenu

Audio2

Enters the Audio2 alarm status submenu

Data

Enters the data alarm status submenu

Config

Enters the config alarm status submenu

For information regarding the alarms and their individual interpretations,

refer to Annex D, Alarm Categories and Conditions.

C.4.3

 

Input Menu

The input status menu provides information regarding the quality of the

input signal.

Table C.26: Input Status Menu, QPSK Input

Display title: STATUS: INPUT

Description

Section

BER(PostV)

Provides the post Viterbi BER measurement, in logarithmic
annotation.

Eb/No margin

Provides the margin to an unacceptable Eb/No. (Single bit energy
to normalised noise level ratio.)

Lock freq

Provides the frequency at which the demodulator has locked.

Table C.27: Input Status Menu, ASI Input

Display title: STATUS: INPUT

Description

Section

Packet length

Reports No sync, 188 or 204 bytes incoming ASI TS

C.4.4

 

Signal Menu

The signal status menu provides information on the incoming transport

stream.

Table C.28: Input Signal Status Menu

Display title: STATUS: SIGNAL

Description

Section

Pkt OK (sec)

Counts the number of seconds since the last sync break.

Bit rate

Reports the current total bit-rate of the incoming transport stream

Video >

Enters the video signal status submenu

C.4.5

Audio >

Enters the audio signal status submenu

C.4.6

Audio2 >

Enters the Audio2 signal status submenu

C.4.7

PTS >

Enters the PTS status submenu

C.4.8

VBI >

Enters the VBI signal status submenu

C.4.9

Data >

Enters the Data signal status submenu

Summary of Contents for TT1220 Series



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands