TANDBERG TT1220 Series Instruction Manual Download

Page: 89 / 114

Menus

Instruction Manual: Professional Receivers and Decoders (IRD)

Page C-11

ST.TM.TT1220.1

C.3.17

RS232 Setup Menu

The RS232 setup menu allows the user to enter the configuration of the

two RS-232 ports on the TT1220, the remote port and the LS data port.

Table C.19: RS232 Setup Menu

Display title: ADV: RS232 SETUP

Description

Section

Remote>

Enters the remote setup submenu

C.3.18

LS Data>

Enters the LS data setup submenu

C.3.19

C.3.18

Remote Menu

The remote menu contains the parameters that has to be configured for a

remote control computer / device to work correctly.

NOTE…
TANDBERG Television’s remote control or software upgrade software requires the use of a

null-modem (crossed) RS-232 cable, not a straight cable.

Table C.20: Remote Menu

Display title: SET: REMOTE

Description

Section

Baud rate

Sets the baud-rate for the communication with the external device.
1200, 2400, 4800, 9600, 19200, 38400, 57600 and 115200 baud
selectable.

Data bits

Sets the number of data bits. 7 or 8 selectable.

Stop bits

Sets the number of stop bits. 0.5, 1.0, 1.5, and 2.0 selectable.

Parity

Sets the parity. The TT1220 only accepts “none”

Flow control

Sets the flow control. None or s/w selectable.

CAUTION…

When software upgrading the TT1220 via RS-232 and the TANDBERG Television software upgrader

(UPGRADE.EXE), it is important that the baud rate is set to 38400, the data bits to 8, the stop bits to 1,

the parity to none, and the flow control to none. If this is not the case, the UPGRADE software might fail

to work.

Summary of Contents for TT1220 Series



















































































































Search results

Summary of Contents for TT1220 Series

Reviews:

Related manuals for TT1220 Series

Brands by name

Popular brands

TANDBERG TT1220 Series, Instruction Manual

Search results

Summary of Contents for TT1220 Series

Reviews:

Related manuals for TT1220 Series

Brands by name

Popular brands