Setting the Loop ID to Provide Additional Loop IDs
If Feature Switch 3 on the Ultrium Tape Drive is set to
ON
(see
1
in Figure 6 on
page 16), the LID/status connector
2
has the following definition:
v
Pins 1 through 7 are used to set the LID.
v
Pin 8 overrides pins 1 through 7. If pin 8 is jumpered, the drive will use its vital
product data (VPD) to set the AL_PA. The enclosure can set the AL_PA in VPD
through the RS-422 interface.
v
Pin 9 is ground.
Note: Feature Switch 3 does not support LEDs on an enclosure. Therefore, when
Feature Switch 3 is set to
ON
, the drive can report Fibre Channel problems
(error codes 8 and F) on the single-character display, but not by using the
enclosure’s external indicators.
To set the AL_PA:
1. Determine an unused AL_PA address for the drive and refer to Table 4 for its
corresponding LID.
2. Locate the LID/status connector on the drive (see
2
in Figure 6 on page 16).
3. Jumper pins 1 through 8 as shown in Table 4.
Table 4. ID Settings that Provide Additional Loop IDs. The table lists the LIDs, corresponding AL_PAs, and definitions
of the jumpers on the connector pins. Feature Switch 3 must be set to
ON
.
LID
AL_PA
PIN
LID
AL_PA
PIN
1
2
3
4
5
6
7
1
2
3
4
5
6
7
0
EF
-
-
-
-
-
-
-
21
B1
-
G
-
-
-
-
G
1
E8
-
-
-
-
-
-
G
22
AE
-
G
-
-
-
G
-
2
E4
-
-
-
-
-
G
-
23
AD
-
G
-
-
-
G
G
3
E2
-
-
-
-
-
G
G
24
AC
-
G
-
-
G
-
-
4
E1
-
-
-
-
G
-
-
25
AB
-
G
-
-
G
-
G
5
E0
-
-
-
-
G
-
G
26
AA
-
G
-
-
G
G
-
6
DC
-
-
-
-
G
G
-
27
A9
-
G
-
-
G
G
G
7
DA
-
-
-
-
G
G
G
28
A7
-
G
-
G
-
-
-
8
D9
-
-
-
G
-
-
-
29
A6
-
G
-
G
-
-
G
9
D6
-
-
-
G
-
-
G
2A
A5
-
G
-
G
-
G
-
A
D5
-
-
-
G
-
G
-
2B
A3
-
G
-
G
-
G
G
B
D4
-
-
-
G
-
G
G
2C
9F
-
G
-
G
G
-
-
C
D3
-
-
-
G
G
-
-
2D
9E
-
G
-
G
G
-
G
D
D2
-
-
-
G
G
-
G
2E
9D
-
G
-
G
G
G
-
E
D1
-
-
-
G
G
G
-
2F
9B
-
G
-
G
G
G
G
F
CE
-
-
-
G
G
G
G
30
98
-
G
G
-
-
-
-
10
CD
-
-
G
-
-
-
-
31
97
-
G
G
-
-
-
G
11
CC
-
-
G
-
-
-
G
32
90
-
G
G
-
-
G
-
12
CB
-
-
G
-
-
G
-
33
8F
-
G
G
-
-
G
G
13
CA
-
-
G
-
-
G
G
34
88
-
G
G
-
G
-
-
14
C9
-
-
G
-
G
-
-
35
84
-
G
G
-
G
-
G
15
C7
-
-
G
-
G
-
G
36
82
-
G
G
-
G
G
-
16
C6
-
-
G
-
G
G
-
37
81
-
G
G
-
G
G
G
18
IBM Ultrium Internal Tape Drive
|
|
|
|
|
|
|
|
|
|
|
|
|
Summary of Contents for LTO 1
