background image

English

WIB-31 | WIB-32 | WIB-33

Settings for the dim switch

Name of CVs /
Registers

CV-
no.

Reg.
no.

Input value
(Default) 

Value in CV#115
0

16

Function keys
for activating
the dim switch
(via LDR)

112 37

1 ... 255 (8) F1

F5

1

F2

F6

2

F3

F7

4

F4

F8

8

F0

F9

16

F10

32

F11

64

F12

128

It is possible to activate the function with several function keys. Remark: If you want to assign
the function keys F5 to F12, you have to set the value "16" CV#115 first.

 

Factory settings: The dim switch can be activated with F4. 

Name of CVs /
Registers

CV-
no.

Reg.
no.

Input value
(Default) 

Remarks and Tips
Settings

Sensivity of 
the LDR 

(light 

depending 
resistor)

113 38

1 ... 255
(176)

= Limit value of the 
surrounding lighting, when 
the LEDs and the outputs are
switched on or off.
A higher value causes the 
switching operation to be 
activated at a greater light 
intensity. 

Remark: In default settings the LEDs and the function outputs are switched on when the 
surrounding lighting under-runs the limit value. When programmed accordingly (in CV#115) 
the performance can be inverted (e.g. to switch the lighting off automatically in a shadow 
station).

Settings for the orientation light 

Name of CVs /
Registers

CV-
no.

Reg.
no.

Input value
(Default) 

Value in CV#115

0

32

Function keys
for activating
the 
orientation
light
 

118 41

1 ... 255 

F1

F5

1

F2

F6

2

F3

F7

4

F4

F8

8

F0

F9

16

F10

32

F11

64

F12

128

It is possible to activate the function with several function keys.

 

Remark: If you want to assign the function keys F5 to F12 to this function you have to set the 
value "32" in CV#115 first.

 

Factory settings: The orientation light is activated with F3. 

Name of CVs /
Registers

CV-
no.

Reg.
no.

Input value
(Default) 

Remarks and Tips
Settings

Brightness of  
the orientation
light 

119 42

1 ... 255 
(16)

The lower the input value the
brighter is the orientation 
light. 

Settings for the fluorescent tubes

Name of CVs /
Registers

CV-
no.

Reg.
no.

Input value
(Default) 

Remarks and Tips
Settings

Simulation 
of a defective
fluorescent
tube

125 47

0 ... 255 (0) LED1

 1

LED2

 2

LED3

 4

LED4

 8

LED5

16

LED6

32

LED7

64

LED8

128

Page 38

tams elektronik

Summary of Contents for 53-03110


























Reviews: