manualshive.com logo in svg

TallyGenicom 6800 Series, Administrator'S Manual

Share
Download
TallyGenicom 6800 Series Administrator'S Manual Download Page 169

Fault Messages

169

Fault Messages Requiring Field Service Attention

If a fault is not correctable by the operator, the fault message is followed by an 
asterisk (*). This usually indicates that an authorized service representative is 
needed. You may try two steps to clear the fault before calling your authorized 
service representative:

1.

Set the printer power switch to O (Off), wait 15 seconds, then turn the 
printer on again. Run your print job again. If the message does not 
appear, it was a false indication and no further attention is required.

2.

If the message reappears, press the 

CANCEL

 key. If the message 

disappears, it was a false indication and no further attention is required. If 
the message reappears, call your authorized service representative.

Table 13. LCD Message Troubleshooting Table

Displayed Message

Can User 

Correct?

Explanation

Solution

12 VOLT FAILED*

No

The power supply 12 volt
output has failed.

Contact your authorized 

service representative.

1

B12 ERROR: PROGRAM 
MISSING*

Yes

The printer does not see 
a program in flash 
memory.

There is no program in printer 
memory. Download printer 
firmware again.

B13 ERROR: NOT 
COMPATIBLE*

No

Attempting to download a 
program that is not 
compatible with the 
printer.

Cycle power to see if the 
message clears, if not, contact 
your authorized service 

representative.

1

B20 STATUS:00% 
DOWNLOAD MODE

No

Status message 
informing the operator 
that software is being 
downloaded. Percentage 
figure indicates 
approximate amount 
loaded into the printer.

No action is required.

B21 STATUS: PRINTER 
RESET

No

Status message 
informing the operator 
that the printer is 
undergoing a system 
reset.

No action is required.

B22 ERROR: 
DECOMPRESS SIZE*

No

Error can only occur 
during a program 
download (corrupt data).

1.

Download program 
again.

2.

Check communications 
cable being used 
(Parallel, USB, or 
Network). If Parallel 
cable is used, reseat 
the PCI Parallel opt 
card.

Summary of Contents for 6800 Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands