manualshive.com logo in svg

TallyGenicom 6800 Series, Administrator'S Manual

Share
Download
TallyGenicom 6800 Series Administrator'S Manual Download Page 159

Configuring the Printer to run a Demo File

159

5.

The output file for download will replace the 

file_name

 extension with 

“.fls”.

Example: 

demo2fls demo.txt <Enter>

This creates the file “demo.fls” that will place “demo.txt” in the Main File 
System when downloaded.

6.

Put the printer in download mode as described in “Manual Two-Key 
Download Sequence” on page 144.

7.

Send the file as described in “Manual Three-Key Download Sequence” on 
page 145. Substitute the file *.fls (e.g., demo.fls) in place of the firmware 

FILENAME.prg

.

The process is complete when the file has successfully loaded into flash 
memory.

To verify that the file is properly recognized and downloaded, look under Test 
Menu -> Printer Tests submenu. One of the printer tests should include 

file_name

.

Configuring the Printer to run a Demo File

This facility makes no attempts to identify which emulation a particular demo 
file is designed for. The user must configure the printer for the appropriate 
emulation before invoking the demo. The demo will inherit all menu 
configuration parameters when executed. The user is responsible to properly 
configure the forms size, typeface, orientation, etc. This facility will not restore 
any configuration settings when the demo file is finished printing.

Starting a Demo File

The demo file is initiated by selecting its Flash File name within Test Menu -> 
Printer Tests submenu, then pressing ENTER. This causes the printer to go 
online and start printing the demo file. Once the demo file starts, it repeats 
automatically until the demo file sequence is stopped.

IMPORTANT

DO NOT run a demo file if currently running another type of test or host 
job. This will cause unexpected results. Similarly, DO NOT send host 
jobs when running demo tests.

Pausing a Demo File

The demo can be paused by going OFFLINE (pressing the ONLINE button). 
To resume printing, go back ONLINE.

Stopping a Demo File

The demo is stopped by executing a soft reset on the printer (pressing the 
LEFT and RIGHT keys simultaneously). This allows normal operation to 
resume.

Summary of Contents for 6800 Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands