K11823;18/34
- 18 -
MS=1 SS=7
MS=1 SS=7
ID: CAMERA-1
FC1600FPL
ID not specified
ID specified
FC1600F
Ｐ
L
[VX.XX]
Menu display of Setting Group 2
MENU2
MENU
: ON
-
: (Reserved)
-
: (Reserved)
PWC
: DISABLED
MS=A SS=7
MF=0008.0000
S.FORM:
The current shutter operation mode is displayed. The left is either
continuous (NORMAL) or asynchronous (ASYNC), and the right is
either high speed (HIGH) or low speed (LOW).
SCAN:
The current scanning system is displayed. It is either all pixel
readout scan (NORMAL) or partial readout scan (PARTIAL).
(
→
See “Priority relationship among scan mode setting items”
described in another section
PWC:
Whether the position “9” of the shutter switch for the asynchronous
shutter operation is used (ENABLED) or not used (DISABLED) is
selected.
BZ:
This is to switch between (ON) and (OFF) for the confirmation
sound to be activated when switch manipulation is made.
BAUD:
The baud rate used for RS-232C communication is displayed.
H-RESET: Whether the horizontal timing resetting(initialization) is enabled
or not enabled is selected. If it is enabled, H(horizontal
synchronization) timing is reset when the trigger signal is input
in the asynchronous shutter operation mode.
Vinit2:
The polarity of the trigger signal via CC1 of Camera Link is set.
The factory default is negative logic (NORMAL). When
(INVERTED) is selected, positive logic input is used.
STRB-C:
ON/OFF is set for the strobe signal (STRB) output for the
continuous shutter operation. When (ON) is selected, the
strobe signal is output even in the continuous shutter mode.
(Note) The strobe signal is always output in the asynchronous shutter mode
regardless of this setting.
PATTERN:
This is to switch between (ON) and (OFF) for the test pattern
output.
bit This is to switch between (8 bit) and (10 bit) for the bit rate of
image output.
* The following items are for display only; they cannot be directly changed
on the menu. These are automatically updated when a corresponding
change is made using the switches:
MS=
The current position of the mode switch is displayed.
SS=
The current position of the shutter setting switch (EXP.) is
displayed.
MF=
The information (16 bits x 2 sets) of the internal mode flags of the
camera (internal flags to determine operation) is displayed in the
hexadecimal system. The details of the internal flags are
described later.
Tc=
The current internal temperature of the camera is displayed in Celsius. The temperature data are refreshed
every 0.4 seconds.
[ID information display]
The ID code and other information set by the user for each camera can be saved in the camera (with the use of the serial
communication). The settable maximum number of characters are 15, and alphanumeric characters (both upper and
lower cases) and some special symbols such as”+” and “-” excluding the control codes are used.
(
→
Refer to the section of “Serial Communication Control” for the details.)
The ID code set by the user is displayed on the lower left of the “Menu Display of Setting Group 1” by the OSD function;
this allows the user to confirm the setting content (ID: onward).
(If the ID code is not set, the camera model name is displayed instead.)
The bottommost and right figure shows an example where “CAMERA-1” is set as the ID information.
[Change of setting]
Perform the procedure described in another section: “(6-2 ) How to set operation mode” when changing the current setting
while referring to the information displayed by the OSD function.
When the position of the mode switch is changed, a flashing “ * ” mark appears on the left of the numeric value or the
parameter of the item corresponding to the switch position to indicate that the setting can be changed using the
UP/DOWN switch.
FC1600F
Ｐ
L
[VX.XX]
Menu display of Setting Group 3
MENU 3
MENU
: ON
BZ
: ON
BAUD
: 9600bps
-
: (Reserved)
-
: (Reserved)
Vinit 2
: NORMAL
STRB-C : OFF
MS=C SS=7
MF=0008.0000
FC1600F
Ｐ
L
[VX.XX]
Menu display of Setting Group 4
MENU 4
MENU
: ON
PATTERN : OFF
bit
: 8bit
MS=C SS=7
MF=0008.0000
