background image

COPY

‑A7‑

Sep./12/ 12

0

RPM

SA

E

Po

we

r(

PS

10‑15カム

15‑20カム

20‑25カム

25‑30カム

Be sure to use the supplied new snap ring to reinstall the plate. Do Not use the old snap ring. When performing

the maintenance, be sure to refer to the Owner’s Manual and proceed the tasks.

IMPORTANT NOTICE :

On removing and re-installing the camshaft

Snap ring

Plate

The following camshafts compatible with this kit are available from us. Referring to the list below, please 

select a camshaft to match the use, for your great riding pleasure.

You can choose one as an optional part if it matches your bike after confirming the specifications.

About optional cam shaft:

Cam Shaft Comparison Data List

About the descriptions of camshafts and numbers

The bigger the numbers of XX/YY are, the wider the durations are. With these camshafts, the output power

will produce more to high rpm range.

While the smaller the numbers are, the narrower the durations are. With these camshafts, the output power

will produce more to low-to-mid rpm range. The output features are different from each size.

When purchasing our optional camshafts, please choose the camshaft to suit your riding purpose referring

to the camshaft data chart.

Also, the engine output will vary significantly depending on the used exhaust system, length of inlet pipe, 

carburetor diameter, compression ratio, ignition timing, fuel or the natural phenomenon such as ambient 

  

temperatures or atmospheric pressure.

Note: As these are the data measured on a Dyno Jet, the data differ from the actual driving. Please refer to them

   

just for a reference. The engine power varies significantly depending on the temperatures.

3-5-16  Nishikiorihigashi   Tondabayashi   Osaka    Japan

TEL : 81-721-25-1357

FAX : 81-721-24-5059

URL : http://www.takegawa.co.jp

Co.,Ltd.

10-15 cam

15-20 cam

20-25 cam

25-30 cam

10-15 cam

15-20 cam

20-25 cam

25-30 cam

10/15D camshaft

01-08-0141

15/20D camshaft

01-08-0142

20/25D camshaft

01-08-0143

25/30D camshaft

01-08-0144

Summary of Contents for 01-00-9202






















Reviews: