background image

14

Unit fixing position and Plumbing Layout

● Fixing the base to floor.

*The holes marked are the standard fixing holes to floor. Please ensure to fix the base to floor at 4 points.

(Anchor bolt M8-70 (4pcs.) or Hex head tapping screw M8-60 (4pcs.)).

*If the standard fixing holes cannot be used, please use the spare holes nearby. 
*If in case the floor is not strong enough or enough strength cannot be secured, 

please increase the numbers of fixing bolts/screws to be used.

90

185  (Raising pipe area)

55

80

Water Supply

1/2”  13m/m (Rise 60mm)

Hot Water Supply

1/2”  15m/m (Rise 60mm)

Drainage

VU40 (Rise 50mm)

Chair Side

Distance to the wall or 

the furniture 

: Min.1350mm

(Including working 

 space 2600mm)

Distance to the wall or the 

furniture : Min.1350mm

(Including working space 

 2600mm)

Distance to the wall or the furniture : Min.1100mm

(Including working space 600mm)

229

187

205.4

169

13

84

416

(

Base size

)

155(Raising pipe area)

60×90(Sub-floor base (wood))

241

293

314(Base size)

   

Standard fixing 

hole to floor

Outer line of base

Outer line of base cover

This distance will vary depending on the chair. 

Please inquire Takara Belmont.

Center pf pipe

162

Summary of Contents for RS

















Reviews: