background image

13

シャンプーユニットにガタつきがあるときは、取付部分のボルトをもう一度確認してください。

Hook

Hook

Shampoo basin

Seat side

Neck cushion

Fastening pin

After installation

Caution

(1) Set the neck cushion to the end of basin

     in the direction as shown in the image. 

(2)  Attach the hooks of the neck cushion to the

 fastening  pins inside of basin.

*

 

Take care not to lose the fastening pins.

(3)  Adjust the shape of the neck cushion and attach

the basin side hooks of the neck cushion to the 

fastening pins outside of basin.

Caution

 

Be sure to execute the inspection without fail to prevent accidents during operation.

 

Be careful about the installation direction. 

If the cushion is installed in the wrong 

direction, it may contact the backseat.

Caution

 

Execute the installation using the following 

procedures:

●Inspection

Inspect the following items.

(1) Check that there are no missing screws or other parts.
(2) Check that there are no loose parts on the shampoo unit .If any part of the shampoo unit is 
      loose, check the bolts at the joints again.
(3) Check that there are no cracks or contamination on the basin.
(4) Check that there are no problems, such as flaws on the external appearance.
(5) Check that there are no water leaks on the floor.

●Attach neck cushion on the basin

Summary of Contents for RS

















Reviews: